Question about 1997 Audi A4

1 Answer

Where is the bleed screw on 1997 audi a4 1.8 - 1997 Audi A4

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 51 Answers

Which bleed screw???????????????

Posted on Nov 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Audi tt leaking clutch fluid


Replace the hydraulics. This video may help
2000 Audi TT Clutch Replacement

Jun 11, 2017 | Cars & Trucks

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

Bleeding a4 (b6)cooling system?


bleeder screw on metal water pipe above inlet manifold. loosen bleeder screw, fill coolant at coolant resivoir untill all air pushed out bleeder.

May 12, 2010 | 2002 Audi A4

1 Answer

How do i change front brake hose on my 98 audi a4? where is it located?


Its located on the brake caliper and goes up to the brake line,To change just remove the high pressure fitting from both ends [very basic job]Fit the new pipe ,but now you have a new pipe but full of air!.To bleed out the new pipe just open the bleed screw [looks like a grease nipple on the top of the brake caliper]and connect a small piece of hose [must be a tight fit on the bleed screw]with the bleed screw loose and the hose fitted just fit the other end in to a container of brakefluid and press the brake slowly up and down till all the bubbles are gone{dont forget to top up your reservoir before you bleed it!!]as if the reservoir runs dry you will need a special bleeder to bleed the brakes [it requires 2 bar or 30 psi pressure to bleed out the system after the reservoir goes dry]

Mar 08, 2010 | 2004 Audi A4

1 Answer

Audi a3 1996 1.6 5 speeds model. 1st flexi clutch pipe split..no clutch replaced pipe now no gear change..could it be worn clutch? car is in garage! help tp


First you must air bleeding out from inside hydraulic clutch acting system ! On the slave cylinder you will find an aeration screwed ventil provided for air bleeding. See picture below:

ee99bec.png Two person are necessary for this operation. One person for acting the clutch pedal and another person for air bleeding out from inside hydraulic clutch acting system by unscrewing the aeration ventil from slave cylinder. This operation is difficult, and must spend some time for successful result!

Jan 28, 2010 | 2005 Audi A3

2 Answers

Heating doesnt work 2001 Audi 2.8l a4


Sounds like the water level is low. Often the water pipes are higher than the radiator and require bleeding when the car is running, see if there are any bleed screws on the hoses to release the air.

Dec 29, 2009 | 2001 Audi A4

1 Answer

Audi a3 rear brake pads


Leave the bleed screw alone, remove the cap on the master cylinder, and wind the piston clockwise.

Apr 03, 2009 | 2005 Audi A3

2 Answers

1997 audi A4 heater blowing cold air


You probably have a leak in your oil cooler. This is causing the oil to bleed into your cooling system causing the "thick brown liquid". This in turn will also cause your engine to over-heat since the cooling system is contaminated.

Feb 25, 2009 | 1997 Audi A4

1 Answer

I want to replace the rear disk pads on my a-6 Quattro 3.0; can I safely use one of those compressor kits from a parts place to compress the pistons, any tricks to share ?? and anything to worry about...


I have taken the brake caliper of the rear passenger side and renewed the seals in it i have also renewed the brake pads in that wheel i have tried to bleed it before renewing the pads in the outherside but when i open the bleed nipple and push the peddle down there is no braked fluid coming out i also renewed the nipple.When you take the brake pipe off the caliper ther is still no fluid coming out also there is no pressure on the pedal 1997 audi a4 1800

Jul 26, 2008 | 1998 Audi A4

2 Answers

Removing rear bumper on Audi A4 1997 to fit tow bar


Did you get the solution to this, I have the same problem

Jul 07, 2008 | 1997 Audi A4

Not finding what you are looking for?
1997 Audi A4 Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...