Question about 2005 Dodge Ram 1500

Open Question

Replace ball joints on a 2005 dodge ram - 2005 Dodge Ram 1500

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 333 Answers

SOURCE: upper and lower ball joints

Your better off have it done bt a tech because you need a press to press them out and in. Also you will have a warranty witk the work. You want to be safe messing with your steering and suspension. I hope this helps.

Posted on Dec 05, 2008

  • 160 Answers

SOURCE: 1997 DODGE RAM 1500

 just tare the axels down and pull the brake callipers and brake disks, to get to the ball joints. un bolt the nuts and take the peice holding the ball joints in and  then press out . But you need a ball joint press if you wanna do it on your own

Posted on Jan 06, 2009

Molson02536
  • 3854 Answers

SOURCE: Ball Joints

I highly recommend that you have a press available, they dont screw in unfortunatly.
To change uper ball joints; Remove tire Pull codder pin and remve nut Tap ball joint out of wheel/ brake assembly Remove upper control arm compleatly Use Press to push old ball joint out of controll arm.
A torch may be nessisary to heat controll arm. Press new ball joint all the way into controll arm Reinstall every thing Get a professional front end alignment. 

Good lcuk and hope this helps.

Posted on May 05, 2009

  • 7 Answers

SOURCE: i have a 1997 dodge

I REPLACED THE ENTIRE FRONT END OF MINE AND WE USED A HYDRAULIC JACK AND THE WEIGHT OF THE TRUCK TO PRESS THEM OUT AND A BALL PING HAMMER TO PUT THEM BACK.

Posted on May 26, 2009

  • 72 Answers

SOURCE: Upper and lower ball joint replacement

to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 dodge ram 1500 lower aframe replacement


remove the axle nut and pull the axle off of the hub. Now you should have enough room to get the ball joint out.

Jan 30, 2015 | 2006 Dodge Ram 1500

1 Answer

2007 dodge ram upper ball joint replacement


where did the replacement come from and did they give you the right one...repost

Feb 09, 2013 | 2004 Dodge Ram 1500

1 Answer

How do you replace the ball joints on a 2005 dodge ram 2500 2 wheel drive


lowers are pressed in and out. if uppers are on yours depending on the model they should be riveted on. If not the control arm is replaced instead

Jun 17, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

How do i replace ball joints on 1997 dodge ram 1500


jack up truck support truck remove brake caliper and support the caliper dont let it hang by the hose remove cotter pin from bottom of ball joint remove castle nut from ball joint use ball joint press to push ball joint up and out then use press to push in new ball joint make sure you grease them when you are finished both uper and lower press up and out.

Feb 02, 2010 | 2008 Dodge Ram 1500 2WD

1 Answer

Changing front ball joints on Dodge 2500 2005


can it not be done without removing the hub ?? dont think you can get hub off without removing the track control ball joint?do you have the right tools??

May 30, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

Ball Joints


I highly recommend that you have a press available, they dont screw in unfortunatly.
To change uper ball joints; Remove tire Pull codder pin and remve nut Tap ball joint out of wheel/ brake assembly Remove upper control arm compleatly Use Press to push old ball joint out of controll arm.
A torch may be nessisary to heat controll arm. Press new ball joint all the way into controll arm Reinstall every thing Get a professional front end alignment. 

Good lcuk and hope this helps.

May 04, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

How do you change the lower ball joints on a 2005 1500 4x4 ram


It is also possible to buy the complete lower control arm, but again, just as the last guy stated, it does have to be aligned, You may want to get the ball joint press(special tool) from a store with a tool lending program.... Canadian Tire, Pep Boys, whatever is in your area. If you need further help just give me a shout, I'll do what I can...
Good Luck...
R

Feb 28, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

1997 DODGE RAM 1500


 just tare the axels down and pull the brake callipers and brake disks, to get to the ball joints. un bolt the nuts and take the peice holding the ball joints in and  then press out . But you need a ball joint press if you wanna do it on your own

Jan 06, 2009 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...