Question about 1996 Isuzu Rodeo

Open Question

My a/c wont work in my Holden Rodeo ute.Compressor not engageing,I have heard that their is a relay hidden under the dash some where,Fuse is fine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 9 Answers

SOURCE: A/C compressor won't engage

have you had you freon checked?? there is a safety on that compressor if your system gets to low it will not allow the unit to run.. irongod

Posted on Apr 06, 2009

  • 3 Answers

SOURCE: 1994 isuzu holden rodeo injection timing adjustment

try u-pull our patrs

Posted on Sep 12, 2008

Ray190te
  • 61 Answers

SOURCE: repair oil pump for a 3.2l 2001 holden rodeo ute

Yep the pick up is in the sump

Posted on Jan 18, 2009

  • 40 Answers

SOURCE: no dash/instrument lights,no tail lights,no park

I would recommend replacing your relay. From what you have described your battery might be bad. The clicking you heard is consistent with this. Natuarally though the relay is probably cheaper to fix. Also if you're car was slow to start or was dragging when you were trying to start it, you may have a bad starter, which would cause the aforementioned

Posted on Jul 16, 2009

  • 4088 Answers

SOURCE: no pressure clutch pedal goes straight to the floor 1988 holden r

If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Posted on Aug 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Holden Colorado wont start and no dash lights


Check your ecm fuse, or your main power relay fuses, basically just check all the fuses under the dash and under the hood, if there are a few relays under the hood, you can try and swap the ac relay with the power relay as long as they have the same numbers on them. If all the fuses are good, it is most likely a relay, or the ignition switch itself

Jul 11, 2016 | Holden Cars & Trucks

1 Answer

I just purchased a 98 Holden Rodeo ute and the heater fan is not working, can you tell me is this a big job to replace or is it something I could do myself if so does the whole dashboard need to come off...


Easy job if you are mechanically minded, first check the resistor, this is where the electrical wiring plugs in under the dash on the glovebox side, there should be 2 phillips head screws. If this is ok then it may be the motor which should be pretty easy as well and should come out under the dash on the passenger side. I hope this helps.

Mar 14, 2013 | Cars & Trucks

2 Answers

Vt aircon compressor wont engage


check the freon, if there isn't enough it won't engage, could also be the low pressure switch or a fuse.

Sep 05, 2012 | Holden Cars & Trucks

1 Answer

Electrical problem. 2000 holden rodeo


battery capacity is irrevelent and fuses blow because of excessive current flow not from battery size
have an auto electrician check ot out as it may be a bad ECM
you just say fuses but each fuse has a capacity and belongs to a particular circuit so if it is a high amp fuse check thew units on that fuse for shorting out
ie 60 amp fuse for ignition, ECM , power steering pump
5 amp fuse for clearance lights etc

May 20, 2017 | Cars & Trucks

1 Answer

Rodeo petrol starts but wont rev


Holden Rodeo 1989 2.6mpi , start and only runs for 2 or so seconds themselves stalls, after putting on a fuel peesure gauge, fuel looked okay and slowly dropping, found the ECM relay was intermittently switching on and off, gave it a tap and the engine kept on running, relay not repairable, replace with new part. Located in the fuse and relay box on the right hand side of engine bay next to battery. Hope this helps.

May 24, 2012 | Holden Rodeo Cars & Trucks

1 Answer

Condensor on compressor wont engage,,,1996 mercury gran marquis


relay should be located under the hood next to the battery. There is a fuse panel with many different relays. Check in your manual under "roadside emergencies" and find the relay for the A/C compressor. very common problem.

Jul 11, 2009 | 2000 Mercury Grand Marquis

1 Answer

1994 rodeo a/c compressor will not come on.


hot wire the compressor to make sure if it is working or not. If all the fuses are working and the compressor is not running then your compressor is defective.

Jul 03, 2009 | 1999 Isuzu Rodeo

1 Answer

1994 rodeo a/c not cooling


put gauges on it first to see if it has enough freon to make compressor come on

Jul 03, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...