Question about 2005 Jeep Grand Cherokee

Open Question

How to install heater blower for Jeep Cherokee?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

inhisname
  • 76 Answers

SOURCE: Heat/AC Blower fan speed only works on High

hello, this sounds like a bad blower motor resistor!! its cheap and easy to change..if you need more info on locations let me know,, good luck.....marty

Posted on May 27, 2009

michigan man
  • 3533 Answers

SOURCE: blower motor only works on high on 98 jeep grand

you need a temp limited switch and for the most part its close to the blower motor has a small screw on each side with a plug in the middle give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your Jeep dealership in the parts department and they be able to show you what i am talking about and print you off pictures and diagrams showing you where it is located wish you the best of luck Michigan Man.

Posted on Jan 04, 2010

wracefans24
  • 1985 Answers

SOURCE: 1996 jeep grand cherokee blower works but no heat

Since your blower is working and it is a heat issue,thats where we'll start,First thing is have you checked the coolant level in the radiator when engine is cold,make sure it is filled to top,next verify you have coolant in reserve ,Start your van and get it up to normal operation temperature,If your heat gauge on the dash works correctly it should be 190 degrees,Now lift the hood and locate the two heater hoses going into the heater assembly at the fire wall,Both hoses should be hot to hold on to,if both are hot and no heat inside your problem will be the blend air door in heater assembly.
if neither hose is that hot you need to replace the thermostat in the engine to get it up to 195 degrees.
if one hose is hot and one is luke warm then the heater core is blocked and to blame. hope this helps you.

Posted on Jan 12, 2010

Testimonial: "Thanks!!!"

  • 3640 Answers

SOURCE: how to replace 2006 Jeep Grand Cherokee fan Heater

the blower motor is under panel near glove box. remove connector then the 3 mounting screws that hold it in. if changing the motor, use old fan cage from blower to new one, remove retainer clip to take off of motor shaft. CARL,

Posted on Jan 20, 2010

  • 279 Answers

SOURCE: Location of heater blower relay for a 1998 Jeep

Located on the the passenger side,underneath the plastic cover mounted to the heater box.

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove heater blower motor?


1998 ATC Jeep Grand Cherokee Blower Resistor connector ...

? 0:55
www.youtube.com/watch?v=sDFLuenx9aw
Nov 14, 2012 - Uploaded by Freedomautomotive1
1998 ATC Jeep Grand Cherokee Blower Resistor connector Repair Kit (RARE 1/2 Year) ... How to Fix a Chrysler Blower FanThat Only Works on High - Duration: 16:51. ... JEEP2001 FIXING THE HEATER BLOWER CONTROL. ... Jeep Grand CherokeeCenter and Lower Dash Removal - Auto Repair Series ...

Sep 30, 2015 | 1998 Jeep Grand Cherokee

1 Answer

I need information on how to change my blower motor assembly on a 2001 jeep grand cherokee laredo 4x4 4.0


The blower motor is located under the right side of the dash in the A/C Heater housing. Disconnect blower cooling hose. Remove blower connector from retainer and unplug the connector. Remove the 3 blower motor screws and remove blower motor. Reverse procedure to install..


dttech_128.gif


dttech_129.gif

Jun 30, 2011 | 2001 Jeep Grand Cherokee

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Jeep cherokee Heater blower problem


Its not the switch or the controller in the instrument cluster. On my jeep there was a panel on the passenger side under the dash board. It helped me find it by turning on the heater and going toward the sound of the blower. On the backside of the panel was a series of little coils that control the different speeds. one of those coils had been broken.

Feb 20, 2010 | 1989 Jeep Cherokee

1 Answer

My 95 jeep cherokee heater switch on ly works on high


I would try to replace the blower motor resistor first,If that doesnt repair your problem you may wanna try replacing the blower speed switch.The resistor is located under the passenger side of the dash mounted in the heater box.

Jan 30, 2010 | 1996 Jeep Grand Cherokee

1 Answer

How to replace heater core in a 1988 jeep cherokee?


Jeep Cherokee XJ Heater Core

Work for '92 models, but can use it like a reference guide.

6042054.gif

Figure 1

  1. Disconnect battery ground cable, then drain cooling system.
  2. Disconnect hoses from heater core.
  3. If equipped with A/C, remove evaporator/blower housing as follows:
    1. Discharge A/C system, then disconnect hoses from expansion valve.
    2. Disconnect electrical connector and vent tube from blower motor.
    3. Remove console, if equipped.
    4. Remove lower instrument panel attaching screws, then the lower panel.
    5. Disconnect electrical connections from A/C relay, blower motor resistors and A/C thermostat.
    6. Disconnect vacuum hose from vacuum motor.
    7. Cut evaporator/blower housing to heater core housing retaining strap, then disconnect heater control cable.
    8. Pry retaining clip from rear of blower housing flange, then remove the three retaining screws.
    9. Working from engine compartment, remove evaporator/blower housing attaching nuts, then the evaporator drain tube, Figure 1.
    10. Remove right kick panel, then the instrument panel support bolt.
    11. Pull right side of dash outward, then rotate housing downward and towards rear of vehicle until studs clear dash panel. Remove housing from vehicle.
  4. Remove heater core to housing retaining screws, then the heater core, Figure 2.
  5. Reverse procedure to install.
ad4c27d.gif

Figure 2

Personally, I'd pressure test the cooling system then look at the heater core to see if it leaks. It may just be a loose clamp or leaky hose.

Also can check the forum jpmagazine.com

I hope help you; good luck (remember rated this).

Sep 15, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Interior blower controle for a/c and heater only works on high


First is it a computer controlled heater unit?? if so dealer needs to program it.if not...make sure screws are removed and pull!!!!

Aug 18, 2009 | 1998 Jeep Cherokee

2 Answers

Heat/AC Blower fan speed only works on High


hello, this sounds like a bad blower motor resistor!! its cheap and easy to change..if you need more info on locations let me know,, good luck.....marty

May 27, 2009 | 2005 Jeep Grand Cherokee

1 Answer

A/c heater fan no blow


sounds to me like the blower motor resistor, and if I'm not mistaken the resistor and the blower motor are located under the dash on the passengers side. the resistor should have a wiring connection and 2 screws attaching it to the blower case. The a/c and heater blower will not work if the resistor goes out. hope this helps you out a little. Best wishes.

Jan 16, 2009 | 2006 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...