Question about 2006 Ford Laser
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
It is a clear plastic container like a small pill bottle on the fuel line. You just need to unclamp the old one and clamp the new one in place, making sure you fit it excatly the same as way as the old one. It should have an arrow on it.
Posted on Jul 06, 2009
SOURCE: oil filter in civic 97
If you go to a reputable motor factor,
you can only be sold the correct filter for the civic.
As there are soo many variables in engine type, it's almost impossible to tell, oil volume, or which type filter.
However, I will say, be sure that you don't mix semi-synthetic oil, and mineral oil.
Oil changes should be undertaken every 30,000 miles, (unless under extra work load, (in which case, slightly more regularly))
Otherwise, 10/40 or 15/40 grade oil, is perfectly fine.
The trick to not overfilling the oil, is simply just to take your time, clean the dip stick and retry, until you have the correct reading.
Please don't forget to rate:)
Posted on Jul 29, 2009
it basically the same with the other engines...as long as you know what parts to remove. Just make sure that before you remove the belt/s and tensioner/, the timing marks are in the right place. I have changed timing belts without instructions...experience is needed though. I suggest better get a service manual to be sure if this is your first time.
Posted on Aug 10, 2009
Ok, lets take this from the top. I have a 97 f250 diesel. In mid may mine did the same thing. It's either one of two things. You have under valve cover harnesses (uvc). They slide in under your valve covers, you will see two wiring harnesses on the outside of the valve cover gaskets on either side of the block. Ok, it IS possible one of these slipped out of place and killed two of your injectors, causing the horrible running/ low idle/no power/ sounds like the truck is going to stall symptoms. The easiest way to check that is to unplug the wires while the truck is running and see if it kills the engine, if it doesen't unplug the other one on the same side of the valve cover. If both of these don't cause any change then you have a bigger problem, the IDM (Injector drive module).
FAIR WARNING: When you unplug the wires with the truck on it is extremely dangerous, it is 110 volt feed. It can kill you.
OK, the IDM is a silver box, 8"x10" approx dimensions, located on the driver side under the hood, over top the front tire. If you take the wires you unplugged and take a multi meter to them and they are dead, you have a bad IDM. This was the case with my truck. Ford designed the IDM to have a hole in the side to allow condensation to escape from it, unfortunately, this allows water inside and will short out resistors and practically kill half of your engine. Buy a new IDM on ebay for about $380. It takes 5 minuts to put it in.
I hope this helps you out man.
Posted on Sep 11, 2009
Tips for a great answer:
Jan 21, 2017 | Ford Cars & Trucks
Sep 03, 2015 | Ford Cars & Trucks
Sep 09, 2014 | 1998 Ford Laser
Feb 01, 2013 | Ford Laser Cars & Trucks
Jun 03, 2012 | Ford Cars & Trucks
Oct 17, 2009 | 1996 Ford Explorer
Sep 09, 2009 | 2003 Ford E250
Aug 10, 2009 | Ford Laser Cars & Trucks
Jul 06, 2009 | 2006 Ford Laser
Mar 04, 2009 | 1996 Ford Taurus
491 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: