Question about 1994 Chevrolet S-10

Open Question

How do I replace the heater core on a 1994 Chevrolet S10 RWD 2.2L 4 Cyl

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: trying to replace heater core 1994 s10 4 cyl

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide



Heater Core - REMOVAL & INSTALLATION
1994-97 Vehicles
(see Figure 1)

44d2ba8.jpg

Fig. 1: Exploded view of a common heater core and case assembly

  1. Disconnect the negative battery cable and properly drain the engine cooling system to a level below the heater core.
  2. Disconnect the heater hoses from the core tubes near the cowl.
The instrument panel carrier is designed not only to provide access to parts through removal of the carrier components, but the carrier will also tilt downward as a complete assembly to allow access from the top. If this is desired, remove the retainer screws along the top and bottom of the carrier assembly (refer to the figure). The instrument panel will then tilt as an assembly into the cab. It is necessary to unbolt and lower the steering column from the carrier to allow for maximum movement of the instrument panel.
  1. The instrument panel must be removed or repositioned for access to the heater core case. Unbolt and either tilt the instrument panel forward or disengage the instrument panel components and remove the panel from the vehicle. In most cases, tilting the panel forward should be sufficient for the necessary access.
  2. Unfasten the heater core rear case retaining screws, then remove the rear case for access to the heater core.
  3. Loosen the retainers and remove the heater core retaining straps.
  4. Remove the heater core and seals.
To install:
  1. Install the heater core and seals, taking care not to damage the core tubes when inserting them through the cowl.
  2. Install and secure the core retaining straps.
  3. Install the rear case and secure using the screws.
  4. Reposition and secure the instrument panel and components. Tighten the cowl screws to 17 inch lbs. (1.9 Nm) and the lower instrument panel screws to 66 inch lbs. (7.5 Nm).
  5. Connect the heater hoses to the core tubes.
  6. Connect the negative battery cable, then properly refill the engine cooling system.
  7. Run the engine at normal operating temperature, then check for leaks.

Good luck (remember rated this post).

Posted on May 19, 2010

Testimonial: "thanks so much.... i have lost the feeling of hopelessness .... thanks to you.... gmo"

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Heater core replacement 98 chevy S10 2.2L engine


Tyrone, Check the attached links,instruction and guides, the last link has some very good info. and pics. on S10 heater core replacement. Good luck.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Heater core replacement 2000 S10 4 3L slideshow picture
How to Change Heater Core on 1994 Chevy 10 Blazer GMC Jimmy Oldsmobile...
98 GMC Jimmy Heater Core Replacement Video Diary
Heater core replacement procedure 99 S10


Jun 16, 2016 | Cars & Trucks

1 Answer

I have a 94 chevy Silverado 5.7l with 4l60 transmission will a 97 chevy Silverado 4l60 work even if the speed sender is on different side and made different on transmission


Chevrolet / GMC / GEO Transmission Look Up Table

www.autorepairmanuals.biz/page/372807
Blazer, 1993-, 4L60-E. Blazer, 1994 - Up, 6.5L V8 Turbo Diesel, 4L80-E. BLAZER/TRAIL BLAZER/JIMMY, 1995-2003, 4 SP RWD/4X4, L4 2.2L L6 4.2L V6 4.3L ...

Transmission Applications - GM Automatic Transmissions

www.gmautomatictransmissions.com/transmission_applications.php
Avalanche, 2001-06, V8 5.3L 5.7L 6.0L, 4 Spd RWD/4X4, 4L60E. Avalanche, 2004-06... Camaro, 1994-05, V6 3.4L 3.8L, 4 Spd RWD, 4L60E. Camaro .... Monte Carlo, 1997-05, V6 3.8L (W/S.C.), 4 Spd FWD, 4T65E. Monte Carlo ... Silverado, Sierra,1500-3500, 1995-06, V8 4.8L 5.0L 5.3L, 4 Spd RWD/4X4, 4L60E. Silverado ...

4L60E Transmission Rebuilt ' eBay


Dec 27, 2015 | Cars & Trucks

1 Answer

How to change a heater core for a 1994 s10 pickup


Remove the glove box.On the passenger side under the hood, remove the two hoses connected to the heater core. remove the connectors/airlines connected to the box, remove the lever on top of the box.remove retaining screws. two screws hold cor in.-----------------------------------------------------------------
Car Diagnostic software

Nov 14, 2012 | Cars & Trucks

1 Answer

1994 Toyota pickup / 4WD / 4 cyl. Replaced heater core. Checked heater control valve- working correctly. Filled system from upper hoses at firewall to fill heater core. Connected hoses. replaced...


you could try running engine and open top heater core hose highest point should bleed it fully, failing that look at manual should tell how much water is in system

Feb 01, 2011 | 1994 Toyota Pickup

1 Answer

Trying to replace heater core 1994 s10 4 cyl


GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide



Heater Core - REMOVAL & INSTALLATION
1994-97 Vehicles
(see Figure 1)

44d2ba8.jpg

Fig. 1: Exploded view of a common heater core and case assembly
  1. Disconnect the negative battery cable and properly drain the engine cooling system to a level below the heater core.
  2. Disconnect the heater hoses from the core tubes near the cowl.
The instrument panel carrier is designed not only to provide access to parts through removal of the carrier components, but the carrier will also tilt downward as a complete assembly to allow access from the top. If this is desired, remove the retainer screws along the top and bottom of the carrier assembly (refer to the figure). The instrument panel will then tilt as an assembly into the cab. It is necessary to unbolt and lower the steering column from the carrier to allow for maximum movement of the instrument panel.
  1. The instrument panel must be removed or repositioned for access to the heater core case. Unbolt and either tilt the instrument panel forward or disengage the instrument panel components and remove the panel from the vehicle. In most cases, tilting the panel forward should be sufficient for the necessary access.
  2. Unfasten the heater core rear case retaining screws, then remove the rear case for access to the heater core.
  3. Loosen the retainers and remove the heater core retaining straps.
  4. Remove the heater core and seals.
To install:
  1. Install the heater core and seals, taking care not to damage the core tubes when inserting them through the cowl.
  2. Install and secure the core retaining straps.
  3. Install the rear case and secure using the screws.
  4. Reposition and secure the instrument panel and components. Tighten the cowl screws to 17 inch lbs. (1.9 Nm) and the lower instrument panel screws to 66 inch lbs. (7.5 Nm).
  5. Connect the heater hoses to the core tubes.
  6. Connect the negative battery cable, then properly refill the engine cooling system.
  7. Run the engine at normal operating temperature, then check for leaks.

Good luck (remember rated this post).

May 19, 2010 | 1994 Chevrolet S-10

1 Answer

1994 Chevy S10 Pick-up 4 cylinder, sloshing noise, no heat......is this a heater core problem?


no heat on this old of a vehicle definitly can indicate a heater core problem. sometimes flushing core with a hose can save heater core sometimes it will need replaced. make sure all coolant is properly disposed of if u flush core yourself

Nov 07, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

All 3 firing orders for 2.8 chevrolet s10


not sure what u mean by 'all 3 firing orders'.Here are the firing orders for 4 and 6 cyl engines, and plug # locations.
4cyl. is 1-3-4-2 #1 being at the front of the engine
6cyl is 1-2-3-4-5-6 Front of engine Pass. side is #1, front of engine driver side is #2, back to pass side for #3, etc, Hope this answers your question, if not let me know and I'll help some more.

Jan 13, 2009 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
1994 Chevrolet S-10 Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...