Question about 2004 Dodge Stratus

1 Answer

Where is cam sensor located on 2004 stratus - 2004 Dodge Stratus

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

What engine do you have?

Posted on Nov 12, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: 2004 Dodge Stratus SXT 2.4L Coupe

its in the intake air hose close to the throttle body

Posted on Oct 08, 2008

emissionwiz
  • 76164 Answers

SOURCE: 2004 Dodge Stratus 2.7 thermostat location

Finding the thermostat: Follow the LOWER radiator hose to where it meets the engine. It's in there. Most cars that I've worked on have the thermostat at the end of the upper radiator hose, but not this car. Replacing the thermostat: You need to remove the thermostat housing. (It's the piece that the lower radiator hose connects to.) - You do not need to remove the radiator hose from the housing. - First remove the bolt that is holding a bracket. This bracket just holds some wires in place. - Now remove the three bolts that hold the housing to the engine block. These bolts can be fairly hard to turn, but just keep trying. - Gently pry the housing away from the engine block. You can use a flat-head screwdriver to help pry, but do not scratch the mating surfaces of the housing and the block. - Pull out the thermostat, noting that the spring end goes into the engine. - When you put the new thermostat in, you probably want to use a new black rubber gasket, but you might be able to use the old one if you have no choice. Also, I didn't add any permatex or anything and it seems fine. - I tightened the bolts to 22foot pounds, but this might be a little high. Whatever you do, DO NOT overtighten the bolts. Couple other notes: I first removed the air cleaner cover and tubes to get a little more working room. I also unplugged one wiring harness to make more room. Otherwise, I was able to get my big hands in there. A new thermostat did not fix my problem. Here is a description of the problem I was having and the solution: Problem: The temperature gauge was spiking occasionally, all the way into the red. It would spike up and come back to normal. It would spike usually while in idle, but sometimes while driving. Usually about once every twenty minutes. Things I checked first: - The plastic reservior for the radiator was full to the top. - The electric fans were running, and running on high speed. - The car had working heat. - Replaced the thermostat. Did nothing to help the problem. Problem Found: - Vapor lock. Even though the reservior was full of fluid, it had previously gotten too low and the system sucked in some air. Once that happens, it doesn't matter if the reservior is full, the cooling system will not draw in the coolant. This is because filling the plastic reservior does not pour coolant directly into the cooling system. The coolant is sucked into the cooling system through a tube, like drinking soda through a straw. So the reservior, where they tell you to add coolant, was full but the cooling system (radiator, engine, pump, etc.) was almost out of coolant and wasn't able to draw in any more. Solution: When the engine is cool, open the metal radiator cap that's sticking right up out of the engine. It can be found by following the upper radiator hose to the engine. There is a tall metal tube with a metal cap on it. Pull that cap off (when it not hot) and fill it up with radiator fluid. (I use radiator fluid that's pre-diluted and designed for all makes and models of cars). Idle the car, in park, for about thirty seconds. Stop the engine and put the cap back on. If you're lucky, all the air bubbles are out of the system and you're all set.

Posted on Dec 02, 2008

  • 1596 Answers

SOURCE: cant find cam sensor in 2004 dodge stratus r/t

2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Posted on Feb 12, 2009

  • 1861 Answers

SOURCE: MAF Sensor 2004 Dodge Stratus

If your car has a MAF (Mass Air Flow) sensor, it would be located in the air delivery tube that runs from the air filter box to the throttle plate assembly on the intake manifold. It will have a wiring connector going to it, also. The MAF does exactly what it is called: It "senses" the volume, or "mass" of the air-flow; thusly it needs to be in the intake air tube. If you do NOT have such a device in the air-tube, you have a MAP sensor, (Manifold Absolute Pressure); this is another way of measuring the same air volume, albeit older technology. You will commonly find this device on the firewall, with a vacuum line running to the intake manifold.

I hope that this sheds some light on your question.

Thanks for choosing FixYa for advice!

Posted on Mar 06, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the cam position sensor on my dodge stratus 2004


Its located on top right side of oil I utubed it I only needed one small socket took ten minutes to change don't forget to disconnect battery first

Oct 01, 2013 | 2004 Dodge Stratus

2 Answers

Where is the crankshaft sensor in the 2004 dodge stratus 2.4l


Hi Crystal: It is on the front of the motor, under the starter...

2_4_2012_12_06_11_am.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 03, 2012 | 2004 Dodge Stratus

1 Answer

Where is the cam sensor relay located on a 2004 Dodge Stratus?


If you mean the camshaft position sensor it is on the right hand side of the engine up near the valve cover on the 2.4L 4cylinder engine.

Jan 23, 2011 | 2004 Dodge Stratus

2 Answers

Cam sensor needs to be replaced


Try and Google but depending on engine the 4 cyl. sensor is on the front where the engine and trany bolt together.Hope this helps.

Feb 23, 2010 | 2004 Dodge Stratus

1 Answer

I need to locate the cam sensor for dodge stratus 3.0 2004 model


Please tell us your NOT replacing a cam sensor because someone told you to get a code read at some auto parts store. This is like the flu spreading on this site. Codes DO NOT always mean a sensor is bad. Test it before you throw parts at it.

Feb 08, 2010 | 2004 Dodge Stratus

1 Answer

Camshaft sensor


Cam sensors usally are in the distributer.

Jul 20, 2009 | 2004 Dodge Stratus

4 Answers

Where is the camshaft position sensor located on a 2004 dodge stratus 4 cyl 2.4L engine


the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

Jul 08, 2009 | 2004 Dodge Stratus

1 Answer

2004 dodge stratus with 2.4L


Hi...
The Code P0340 on your Stratus is :
Camshaft Position Sensor Loss signal.
Ok, The first step is check tha condittion on the connector.
For corrosion, bent pins or damaged wires.
If you found that everything is ok.
Replace the Cam Position Sensor.
The Cam Position Sensor, Is common that the Cam fail on this Vehicle and similars of this.
Tha Cam position sensor Is located:
At end of the engine head, driver side. Is attached with 4, 10mm
screw, and the connector at the center of the sensor.

I hope this help on your problem.
Thank you for use fixya...

Aug 29, 2008 | 2004 Dodge Stratus

Not finding what you are looking for?
2004 Dodge Stratus Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...