Question about BMW 325

1 Answer

How to replace rear wheel bearing on 1994 bmw 325i

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 139 Answers

3-Series (Except M3, M Roadster, M Coupe, 318ti & Z3)

1. Raise and support vehicle. Remove wheel(s).
2. Remove axle shaft. See appropriate AXLE SHAFTS article.
3. Remove brake disc. See BRAKE DISC .
4. Screw special tool (33 2 116) onto drive flange with wheel studs. Drive out drive flange with special tool (33 4 201/202/203). See Fig. 33.
5. If necessary, pull off bearing inner race using special tool (00 7 500) and a thrust piece. See Fig. 34.
6. It may be necessary to remove inner wheel bearing race with the following procedure:

  • Detach wheel bearing inner race with special tool (33 4 400) through groove in bearing inner race.
  • According to outside diameter of bearing inner race, use special tool 33 4 401 with: 33 4 405 for dia. 45-51 mm, 33 4 406 for dia. 50-55 mm and 33 4 407 for dia. 55-61 mm in groove. See Fig. 35.
  • Tension special tool 33 4 401 with wrenches 33 4 403 and 33 4 404 until it can still just be turned in groove. See Fig. 36 .
  • Screw in special tool 33 4 402. Detach inner bearing race.
7. Remove circlip. See Fig. 37 .
8. Remove wheel bearing with special tool 33 4 031/ 041/ 042/ 043/ 045. See Fig. 38 .

CAUTION: Do not reuse old wheel bearing.

9. Draw in new wheel bearing with special tool 33 4 041/ 042/ 043/ 047. For inner bearing race 42 mm use special tool 33 4 049 and for 39 mm use 33 4 046. See Fig. 39 .
10. Installation is reverse of removal.
11. Replace stretched or damaged circlip. Ensure correct seating.
12. Pull in drive flange using special tool 33 4 041/ 042/ 043/ 045/ 048. See Fig. 40 .
13. Install brake disc.
14. Install axle shaft.


how to replace rear wheel - 91stt_11.jpg

91stt_12.jpg

91stt_13.jpg


91stt_15.jpg



91stt_17.jpg

91stt_18.jpg

Posted on Nov 12, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: BMW 325i noisy fan bearing Can I replace it.

yes easy you remove the fan and change the whole unit its not repairable

Posted on Nov 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition key wont turn in 1994 bmw 325i


force turn key wiggle steering wheel at same time if wont turn lock needs replaced or repaired,if turns may no work again and needs replaced.

Aug 01, 2012 | BMW 325 Cars & Trucks

1 Answer

BMW 325i noisy fan bearing Can I replace it.


yes easy you remove the fan and change the whole unit its not repairable

Nov 25, 2010 | 2006 BMW 3 Series

1 Answer

My 94 bmw 325I transmission is slipping and not shifting properly. How can I check the fluid level and add fluid if needed? Thanks Vince M


on the drivers side of the transmission under the car is a plug similar to a rear end in the older rear wheel drive cars bmw has
a lifetime tranny fluid setup so take out the plug and fluid should drip out its right behind the shifter cable if it dosent drip out youll need a pump to put it in you can get these at advance auto

May 12, 2010 | 1994 BMW 3 Series

1 Answer

Instuctions for 2001 BMW 325i Heater Core Replacement...


the blower fan on my BMW 530 does not work

May 02, 2010 | 1994 BMW 3 Series

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

Noise in rear left tire BMW 325i 1988


I had the same thing happen, it was the wheel bearing. It's still costly, it has to be pressed in and old one out.

Jan 04, 2009 | 2001 BMW 325

1 Answer

Yellow flashing triangle


The yellow flash triangle comes up when the car attemps to skid. it simply prevents the car from skiding off the road.

Nov 15, 2008 | 1994 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,132 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...