Question about 1989 Ford Ranger

1 Answer

Noise clutch when clutch is disengaged 89 ford ranger 4x4 xlt makes loud vibration noise like bearings when engaged all is quiet changed clutch plate and assembly and still there

Posted by on

  • Anonymous Mar 18, 2014

    noise

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Unfortunately, I would say that the noise does indicate a throw-out bearing that is prematurely worn. Or possibly out of line. If I were in your position, I would take the truck to another mechanic that will give you a written estimate on what he/she "thinks" the problem might be. Then, I would take it to the place where you had the clutch replaced and ask them to "please make the noise go away." I hate do talk bad about mechanics, however it is likely that they did not replace the throw out bearing when they replaced your clutch. I don't know if this has helped you, but I wish you good luck

Posted on Jun 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 F350 6L Diesel, 6 speed manual transmission. Vibration/noise right front when under medium to heavy acceleration, vibration/noise becomes very prominent starting at 1900 rpm in all gears (still can...


Rob, assuming this is a 4X4? Sounds like a bearing. They can vibrate, snap, clunk, all kinds of terrible noises or vibrations.
Axle u joints will also do this. Is it all wheel drive?

Nov 02, 2013 | Ford F-350 Cars & Trucks

1 Answer

300zx clutch/trans noise


Sounds like the release bearing , with the clutch pedal pushed bearing would be disengaged and would not make any noise.

Aug 15, 2013 | Nissan Cars & Trucks

1 Answer

Can't figure out how to hange the clutch on my 1983 ford ranger 4x4 v6


The clutch or the pedal? Or clutch plate, throw out bearing?

Aug 13, 2013 | Cars & Trucks

1 Answer

When i push clutch in it makes a grinding noise.Hard to shift into first.When i come to a stop it acts like it wants to stall


Sounds like the clutch release plate or release bearing are damage or disintegrated. Because one or both of these parts are damaged the clutch does not properly disengage which will result in crunching gear changes at slow speed and also clutch dragging at lights (wanting to stall) etc.

You'll need to split the transmission from the engine block to investigate.

Apr 09, 2012 | 1997 Ford Ranger SuperCab

1 Answer

1992 Ranger 4x4. Have a roaring noise when in 4th & 5th gear. I been told it is probably a bearing in the trans. If so, is it expensive to repair this. It changes as smooth as ever but when you reach...


Only thing I would do to confirm that, is get it on a hoist with someone inside, run it up to speed where noise is present and with an audioscope ( like a stethescope ) used by mechanics, listen and confirm that the noise is actually coming from transmission, and not elsewhere. Then get estimated from reputable transmission repair place before deciding.

Jan 28, 2011 | 1992 Ford Ranger

1 Answer

Just had new clutch fitted on 02 ford focus 1.6 now making noise but stops when i press clutch down


A couple of things comes to mind, when you press the clutch you disengage the transmission. When the clutch is not pressed the transmission still spins inside even when it is in neutral. Sounds like a bearing inside the transmission is making noise, did they put fluid back in the transmission? Also another common source of noise is the throw out bearing, it is on the input shaft, it is the actual part that presses against the clutch pressure plate, usually though they make noise when the clutch is pressed and quiet down when released.

May 07, 2010 | 2004 Ford Focus

1 Answer

My 2004 ford ranger xlt 4x4 won't go into any forward gears, only reverse. When it does go in reverse the engagement is hard?


Sounds like the forward clutches and/or low-reverse one-way clutch. Either way it sounds like it's time for an overhaul

Jul 08, 2009 | 2004 Ford Ranger

1 Answer

5-speed transmission making noise in 3rd and 5th gear


are u sure the alignment (side to side, up and down) of the trans on the bell housingis not out of spec, that will burn the bearings out very quickly.

May 04, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...