Question about 1978 Ford Granada

Open Question

Torque setting for 2.8 v6 ford cylinder heads

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: cylinder head ford zetec escort p reg

Stage 1 = 15Nm
Stage 2 = 40Nm
Stage 3 = Plus 90 degrees or quarter of a turn. Good tip is to mark all the bolts after initial torque setting with tip-ex , i.e. all to the front of the car. When you finish they should all point towards the timing belt.
This is also a good way to make sure you don't miss one or tighten one twice if you are distracted since it is not a torque setting. New bolts should be used by the way as they are stretch bolts. Timing of cams - remove cam cover and you will see a slot on the end of the cams. Opposite end from belt. You need to slip a piece of 5mm flat bar or a long 5mm allen key into then so that the bar rests on the face of the head. Engine should be a tdc.
cheers John

Posted on Dec 17, 2008

Ad
  • 40 Answers

SOURCE: hi i need the torque

hi the cylinderhead torque settings are
STAGE 1, 30Nm (22l bf ft)
STAGE 2, 50Nm ( 337 lb ft ),
STAGE 3, angle tighten another 90 degrees,
STAGE 4 angle tighten another 90 degrees

Cant help you with the cam bearing though sorry

Posted on Jan 07, 2009

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

alicantecoli
  • 22156 Answers

SOURCE: require ford escort rs 2000 1976 torque settings head bolts

2lt overhead cam with them horrible tappet adjusters,cast iron head but valves dont hit the head if the timing belt breaks ,but it does on the 1600 .called a pinto in america .Remember the assembly line well ,have many a fond memory of working on it and the staff canteen on night shift ,what lovely grub we got.Head bolt torque is about 80lbs because i used to pull them down to check them after the machine had tightened them up

Posted on Apr 24, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2004 ford explorer xlt v6 4.0l gas. need a o2 sensor diagram. I need names and description. for example bank 1 sensor 2 after catalytic converter


https://www.google.com/search?q=1998+BMW+318i+Automatic+Torque+settings+Head+gasket&biw=1360&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwie8o3ix8_QAhUJRSYKHdIXBrkQsAQIKQ#tbm=isch&q=2004+ford+explorer+xlt+v6+engine+firing+order

Hope this helps

Bank two are the even cylinders. Follow exhaust manifold on the side. You will find an O2 sensor just after or on the manifold, before the catalytic converter. Then, look after the catalytic and you should find another O2 sensor, this is the one you mention in your post.

Nov 30, 2016 | 2004 Ford Explorer XLT

2 Answers

Cylinderhead torque settings


I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

Aug 22, 2014 | 1995 Pontiac Grand Am

2 Answers

Heatbolt torque settings for audi 2.8 v6 30 valve quattro 1998 sedan


I assume you mean "Cylinder Head Bolts".

Tighten bolts in two-step sequence (See diagram)
Step 1 = 44 Ft. Lbs (60 N.m)
Step 2 = Additional 1/2 turn

These are "torque-to-yield" bolts and NEW bolts must ALWAYS be used when the cylinder head bolts are removed.


4_18_2012_11_18_43_pm.gif

Apr 18, 2012 | 1998 Audi A6

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

1 Answer

Cylider head torque specs ford windstar 1996 3,8 cylider V6


Position the cylinder head on the cylinder block. Tighten the cylinder head bolts in 2 steps following the proper torque sequence. The first step is 37 ft. lbs. (50 Nm) and the second step is 68 ft. lbs. (92 Nm).


98c7056.gif

Oct 21, 2010 | 1996 Ford Windstar

1 Answer

I need head bolt torque specs. for a 2002 ford f150 v6


Torque Specifications for Ford 4.2L-256ci-V6
These bolts are torque and turn procedure!
STEP 1: 14 FtLbs STEP 2: 29 FtLbs STEP 3: 36 FtLbs STEP 4: LONG Bolts Loosen 3 Turns - re-torque to 33FtLbs STEP 4: SHORT Bolts Loosen 3 Turns - re-torque to 19FtLbs STEP 5: ALL Bolts +180deg turn

Aug 05, 2010 | 2002 Ford F150 Regular Cab

1 Answer

Toyota windom v6 head bolts torque settings


INSTALL CYLINDER HEAD if any bolts broken or deformed , replace it.

7------2-----4--------6
5------3-----1--------8
FRONT sequence head bolts
8-------1-----3-------5
6-------4-----2-------7

CYLINDER HEAD bolts are tightened in three progressive steps
1. 34 Nm ( 25 ft.lb)
2. 90 degree
3. another 90 degree.

double check everythings before install the head,
be sure to install the GASKET correctly.

Hope this can help.

Apr 19, 2010 | 1993 Toyota Camry V6

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

1 Answer

Ford-explorer 2005 v6 petrol cylinderhead tightening torques


a part place can give you a print out on the tor spec advance or auto zone

Jan 14, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...