The question i asked someone did not read my question was i need the skimatics to where the fuse goes to make the turn signals and flashers work i have the new fuse just don"t know where it goes

Do you know what a DVOM - digital volt ohmmeter is ? How to use wiring diagrams to test electrical circuits with DVOM? Do you know how the turn signals work ? What controls them ? More then likely it's a problem with turn/hazard flasher module.

Turn Signal/Hazard Lamps
The IGN E 10 A fuse in the underhood fuse block supplies battery positive voltage to the turn signal switch assembly. Ground for the hazard switch is from G302. The FLASHER 15 A fuse in the underhood fuse block supplies battery positive voltage to the turn/hazard flasher module. When the turn signal switch is placed in either the left or right position, a voltage signal is completed from the turn signal switch to the turn/hazard flasher module. When the hazard flasher switch is activated, a ground signal is completed from the hazard switch to the turn/hazard flasher module. The turn/hazard flasher module then sends an on-off voltage signal to the appropriate turn signal lamps, or to all turn signal lamps for hazard operation through these fuses:

https://s23.postimg.org/vfidva88b/turn_signal.jpg

Click on the link.
The fuse goes hot with the key on, from the fuse it goes to turn flasher, from the flasher to turn signal switch then to turn signals. If you need more info holler.

Hope you can read diagram? Did you check for voltage at turn fuse? Use a test light, goes hot with key on. Use a chassis ground when checking for voltage. The voltage wire from flasher to multifunction switch for turn is orange with black tracer, check that also. Let us know what you find?

Could be a fuse, or the flasher, or the turn signal switch.
Someone would need to check for power at each component.
There should be a flasher for the hazard lights and another one for the turn signals.

Hello! The Purple/Orange wire that runs from the fuse (#8) to the Turn signal flasher before it passes through the flasher and goes to the multi function switch Is grounded; either resistively or solid...If you have a multimeter and a wee bit of experience using it set it on the X10 ohm scale...Turn key off...Pull the fuse that blows...I believe #8...Read from the fuse side that connects to the Purple/Orange wire to ground...If you read to ground; Pull the flasher out and read again...If the ground remains with the flasher out the wire is grounded somewhere along the harness...If the ground goes away when you pull the flasher then the flasher is defective (not my first choice)...The best way to repair is to run a new wire from the fuse to the flasher and cut the Purple/Orange out...

Take this a step at a time and let me know what you find...Guru.............Saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

there are two flasher units plugged into the fuse panel. one is for hazards the other for turn signals.
find the fuse panel by reading the owners manual, do not be surprised if it is to the left of the driver's knee. as the flashers are the same unit, just swap them, if the hazards now work but the turn signals don't you have just figured out what is bad. go buy a new flasher unit at a parts store and put it in the turn signal flasher socket. you use the signals way more than the hazards so your new one should be in the signal socket. most likely someone before you did the same thing and that is why your hazards which never get used, failed.

The way the system works is:
The fuse supplies 12 volts to the flasher unit then leaves the flasher and goes to the turn-signal switch in the steering column.
When you set the turn-signal switch to turn right or left, the switch sends that 12 volts to the front and rear bulbs. The voltage goes through the bulb, lighting the bulb and goes to ground.
If any of these components are not good than the lights will not work.
Check the fuse and make sure it is good, the fuse will be located under the hood at the fuse center.
Let me know if you have a test light and we can proceed from there.
Regards,

Do u mean the hazard flashers work, but not the turn signals? If so, check the turn signal flasher, it should be replaced. If I didn't understand your question, let me know.

Your F--150 has 2 flashers, emergency and turn signal. Both are mounted on the fuse block under the dash. The turn signal flasher is mounted on the front of the fuse panel, the emergency flasher is mounted on the rear of the fuse panel. so replace the turn signal flasher should solve the problem. Let me know how it goes.

What flasher? Electronic Flasher in fuse box under dash? Check ground to wires that are connected to the turn signals and hazzards. Rewire a new ground and screw it to the body of the van and see if that works. If not check fuses 1 and 4 see if they are good. Use a test light and check both sides while plugged into fuse box. If that doesn't work pull and check fuses and clean them to be sure there is a good connection.