Question about 1999 Mercury Sable

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal

  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


How do you get the capierer pin off to put front - snorkelbobby_7.gif

Posted on Nov 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find a video on changing the front passenger side brake pads on a 2002 Sable?


On youtube. Also you never change just one side you always do both or your car will pull when braking.

Aug 28, 2016 | 2002 Mercury Sable

1 Answer

1999 mercury sable, need to pick my car up 2" from the rear cause it sags. Can I adjust the shocks that are on it ( motorcraft xf12-18080 ) are the one's on it now. ??


Sag? How To Fix? - Taurus & Sable Owners' Club

www.taurusowners.com > ... > Suspension, Handling & Brakes

Jun 19, 2010 - 20 posts - ‎6 authors
What causes this and is there anyway to prevent this from happening to my car? ... The springs tend to soften up with age and wear. ... strut in the knuckle. i had to do that in teh rear of my car after putting eibachs in it because it ... To do the mod, the tab (#2) is cut off the strut to allow the strut to be positioned ...

Mercury Sable Problems

forums.edmunds.com > Mercury > Mercury Sable

Mar 15, 2000 - 31 posts - ‎17 authors
I have a "clunking" noise in my 1999 Mercury Sable LS. .... in the sag (look under the drivers side of the car near the back of the front ... band up the cable and back into place on the bracket and my clunk ... #2 - Does anyone with an LS have these same steering problems in ..... Select Make; Model (optional).

Car & Truck Repair Questions, Solutions &


Dec 16, 2015 | Mercury Cars & Trucks

1 Answer

How do i remove the front axle shaft from a year 2000 mercury sable station wagon 3.0 LS Premium


and taking a short pry bar insecure between the end of the CV axle and transmission and just wiggling and prying slightly should pop the CV axle out

Jan 12, 2015 | 2000 Mercury Sable

1 Answer

My front passenger brake is sticking on a 1999 mercury sable


replace the brake hose as they can collapse inside causing the fluid to be trapped and not allowing it to travel back to the master cylinder causing a line lock effect.

May 26, 2014 | 1999 Mercury Sable

1 Answer

Passenger side brake is sticking on in a 1999 mercury sable ls


The most common problems are either a collapsed brake hose or a stuck caliper.

May 26, 2014 | 1999 Mercury Sable

1 Answer

Grinding noise front wheel


1st have the brake pads checked, then if the pads are OK you likely have a defective wheel bearing/hub assembly

Mar 24, 2014 | Mercury Sable Cars & Trucks

1 Answer

Wheelbarrow on 201 mercury sable


The possibilities are depending on whether you hear the sound in the front or back of the car: You have a broken brake pad in the front or a broken brake shoe in the back; there is a bad wheel bearing that needs to be replaced, there is a flat spot on one of your tires.

Jan 11, 2013 | 2001 Mercury Sable

1 Answer

How do i change front brake pad on this car merecy sable 1989 -99


Remove the wheel, remove the 2 bolts holding on the caliper to the caliper carrier. You will need a large C-Clamp or a cailper piston tool. Place an old brake pad against the piston in the caliper and use the C-Clamp to push the brake pad against the piston to collapses the piston into the caliper. Also open the master cylinder cap and place a towel around the area to catch any brake fluid that would come out of the master cylinder as you collapes the piston, this is normal, but doesn't always happen, depending on the level of fluid in the master cylinder. Install the new pads and reinstall the caliper and wheel. Make sure you pump the brake pedal a few times before you take off, to get the pads against the rotor.

Mar 16, 2010 | 1999 Mercury Sable

1 Answer

Pulsating break pedal when braking


At least one of the front brake rotors is warped.

Oct 13, 2009 | 1998 Mercury Sable

1 Answer

1997 Mercury Sable thumping in front end


try to replace the wheel bearings.

Jun 17, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
1999 Mercury Sable Logo

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

fordexpert

Level 3 Expert

5572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...