Question about 2006 Jeep Wrangler

1 Answer


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 5,370 Answers

The Clutch Pedal Position Switch (CPPS) is located
under the instrument panel, attached to the clutch
master cylinder push rod. The wiring harness
connector is inside of the vehicle under the left
side of the instrument panel.This should help.Thanks.Helpmech.

Posted on Nov 12, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Its a stick shift so must put cluch all the way to the floor to start it did this one other time a week ago i pumped the cluch in and out acuple times and it started now i did that a bunch with the cluch...

There is a safety switch on the clutch pedal-it is called a clutch interlock switch. Unless the clutch is depressed (so the switch is on), the power won't pass from the key switch to the starter to start the car. Check your clutch safety switch. It will be up high on the pedal, or mounted close to the pedal so the pedal operation will actuate the switch. It may be defective, or it may have slipped out of position.

Nov 27, 2013 | 2001 Hyundai Santa Fe

1 Answer

Fix starter on a 93 nissin P.U.

I have replaced the starter and the relay and I still don't get the starter to start I have checked the switch on the cluch to see if that was the problem and it seems to be working fine. What else could it be ????

Apr 16, 2013 | 1993 Nissan Pickup

1 Answer

Were is cluch sensor on jetta manual tra

I believe there is a switch on a lot of manual trans cars on the floorboard.This ensures that the clutch pedal is all the way down before the starter is engaged.( I am taking a guess here)

Apr 05, 2012 | 1992 Volkswagen Jetta

1 Answer

Will not start, battery ok ,all lights come on

if a standad check cluch switch on pedal if auto check nutral safty switch under dash at colom 4 stering
also check wires 2 starter r tight and clean dose it click if so tap starter it may go but will need 2 replace starter good luck

Apr 04, 2011 | 2001 Kia Sportage

2 Answers

I turn the key on the truck and it does not start but it has power and i changed the cluch swich

not the clutch switch the truck is not reading your key, you have a passlock II secruity system on this truck and it will not run without reading the key.

Dec 13, 2010 | 1995 GMC Sonoma

1 Answer

When i push the cluch in it doesnt start right a way i have to push the cluch several times before it starts

Down by the clutch pedal, there is a safety switch that allows a signal to be sent to the starter relay. The switch probably has a bad spot inside that is not allowing a good contact. You will possibly need to replace or have the switch replaced.

Nov 01, 2010 | 1995 Toyota Camry

1 Answer

Idles and starts fine, press in the clutch and motor dies? 92 Jeep Cherokee 2 WD

sounds like a bad switch to me loo under dash for switch on cluch it is likely a fault in the anti theft system or the remote starter

Jan 16, 2010 | 1992 Jeep Cherokee Sport

1 Answer

Car won't start when I push in the clutch. I have full battery power. I am looking at the clutch safety switch. Need to know where the location is and if it is something I can replace as a novice car...

On cluch pedal arm under dash. Follow pedal arm up.
CAUTION if you override this switch the car will be able to move (jump) when you crank the starter.

Jun 26, 2009 | 1996 Honda Civic

2 Answers

1992 Ford Ranger - Starts Sometimes.. New Clutch. Help?

take back to dealer and have them check the neutral safety switch on the clutch because if the switch is not adjusted properly you will have this problem

Jan 01, 2009 | 1992 Ford Ranger

1 Answer

Cluch won't dis engage

How long have you had your car? How many miles on it?

Maybe the clutch plate gone, if the plate is not thick enough, you won't change the gear.

Jul 06, 2008 | Mazda MX-5 Miata Cars & Trucks

Not finding what you are looking for?
2006 Jeep Wrangler Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides