Question about 2000 Ford Focus

2 Answers

Ford escort zx2, can't get a pictue of the right way the serpetine belt go on

Trying to get a digram for the serpetine belt, on how it is put on over the right pulleys, [ showing how it suppose to be put on correctly]

Posted by on

  • Anonymous Aug 03, 2008

    I have 2001 Ford Escort and i want know how to put the belt on















×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,036 Answers

Hi there!

As a general rule, fit it over grooved pulleys, then bring it over the tensioner pulley to run on the flat side. It will only go on in one position.

I'll search for a diagram for you if you give the engine details.

Thanks.

Posted on Jun 18, 2008

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 46 Answers

Dunno what year model that is,Cos I'd rather push my holden than drive a ford :P heehee

But here's some '01 model Escort diagrams that should help

' 01 Escort 2.0 SPI with Air-Con
ford escort zx2, can't get a pictue of the right w - 142229261.jpg
-----------------------------------------------------------------------------------------------------------------

' 01 Escort 2.0 SPI no Air-Con

2097682616.jpg
----------------------------------------------------------------------------------------------------------

' 01 Escort ZETEC


1932481606.jpg

Posted on Jun 18, 2008

  • SmarT-Arse
    SmarT-Arse Jun 18, 2008

    Just a friendly reminder for all ...

    Dont forget to show your appreciation and reward those who take the time to help !!!

    All you have to do is honestly rate the answer's level of helpfullness
    by the links below.

    It will show others I'm helpfull & make me know you appreciate my help

    =) Thanks

  • SmarT-Arse
    SmarT-Arse Jun 18, 2008


    Sorry to make another comment ,

    But I forgot to mention that whilst I was researching your problem ,

    I saw an awful lot of Escort zx owners complaining of repeated fan belt failures , not that this is pleasing to hear for you , but I thought I'd bring it up as it may assist somebody in some way..

    Just google ford+escort+zx2+serpentine for more details ,
    you dont even have to add the word +fault !!!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pulley making noise


You have several pulleys with bearings in them. The Serpetine belt rides on several pulleys and there are slight differences in the size of those pulleys.

Usually you take off the Serpetine belt and turn each pulley to detect roughness. Then get the appropriate pulley off and replace it.

Sometimes water pump pulleys also make noise as well as Alternators.

Mar 11, 2013 | Mercury Tracer Cars & Trucks

1 Answer

How to install serpetine belt on a 2002 pontiac grand am 6cylinder


There should be a belt diagram underneath the hood by the latch that will show you how to put the belt on properly there will be a spring loaded tensioner pulley that you will attach a wrench to to push the pulley so it releases tension so you can get the belt on an off

Dec 11, 2011 | Cars & Trucks

1 Answer

2004 ford taurus chirping noise when engine revs


Hello, There are several things which can do this. First, cut off the A/C and then rev the engine as before. If the chirping goes away, the noise was either the A/C clutch or the Serpetine belt slipping with the load. For the A/C clutch, you can try a little rust removal between the drive plate and the pulley with the engine OFF. You can use sandpaper and try to knock off the rust. Then put a little oil on to condition the metal. Then try it with the A/C on.

If the chirp is still there, you have to check bearings on the Pulley tensioner, Alternator, Water pump, and Power steering. It is possible for the Pulley tensioner to have a weak spring or you may have a stretched Serpetine belt. This condition would cause the belt to skip under a load. If the belt is checked with small cracks, just replace the belt. Take off the tensioner and compare the spring tension and wobble in the pulley to a new unit at the Autoparts store.

If still no success, the chirp could be a water pump bearing. The old way off using a piece of wood on the housing of a part while the engine is running is dangerous, but effective. I believe you should have already found your problem before this measure is needed. Dry Serpetine belts make quite a lot of noise and is probably your problem.

I hope my Solution is very helpful to you.

Jun 28, 2011 | 2004 Ford Taurus

1 Answer

I have a 1999 Mercury Sable. A bearing in a pully loked up, think it was airconditioner but not sure, anyways the serpentine belt broke. Is this the timing belt? Can I put another belt on it without...


There is no problem with reinstalling the Serpetine Belt. But what have you done about the pulley that is locked up?

You need to find the bad pulley or you will smoke a belt before you leave the driveway. Unplug the wire on the A/C clutch pulley if the compressor is locked up. You need to do this because the A/C will cycle when the dash is set to Defrost setting as well as on AIR.

The idler pulley is the spring loaded tensioner. It is common to lock up. If this pulley is bad, you can keep using the A/C and just replace the Idler pulley.

Check the Alternator, water pump, anything that turns to find the lockup. The timing is done inside the engine with a steel timing chain and is not a part of the Serpetine belt.

Sep 16, 2010 | Mercury Sable Cars & Trucks

1 Answer

Where the serpetine belt goes what is the bottom right pully? It is grinding against something.... Should I be worried about it?


more than likley its a/c pulley you can replace a/c or get a by-pass pulley from Dorman aftermarket parts they work great put you dont have cool air , quick cheaper fix or get knew a/c unit

Jul 26, 2010 | 1996 Pontiac Grand Prix

1 Answer

Serpetine belt and pulley replacement, idler pulley looks bent, does it maybe shift to allow belt to go on easier?


The pulley moves in and out to put the proper tension on the belt. If it looks bent, it is bent. GM idler pulleys routinely need replacing before the belt does.

Bill B

Apr 24, 2010 | 1999 Oldsmobile Aurora

1 Answer

Tryin to put on serpetine belt i got a diagram but need to know how it fits on


You can put it all of the pulleys, including the "tensioner" pulley except one that is easy to reach. Then with a wrench or socket handle on the tensioner pulley, push or pull on it making slack in the belt giving you enough slack to slip it on the last pulley. The belt is then under the tension created by the spring loaded tensioner pulley.

Dec 31, 2009 | 1996 Chevrolet Cavalier

1 Answer

1993 beretta serpentine belt diagram


well its hard to describe but here goes. the belt will run across the top from the PS pump to the alt. from the alt to the inside of the water pump, then to the outside of the a/c comp . then around the crank pulley, then up to the inside of the tensioner, then up around the outside of the PS pump. It will be easier to put the belt around all the pulleys except the alternator, release the tensioner and with the belt loose, slide it over the alt pulley. GOOD LUCK. I hope you fixed the problem with the belt, they just dont fall off for no reason. ck tensioner pulley, water pump.

Sep 18, 2009 | 1993 Chevrolet Beretta

2 Answers

Replace serpetine belt manual


normally there is a diagram on the shroud of the radiator

Aug 19, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

What is the serpetine belt routing for a 97 chevy tahoe 5.7 ?


looking down onto engine feed belt down to your left around crank pulley, route up putting back side of belt around w/pump then continue rest of belt around outside of remanning acc. leaving top idler last. put 3/8 drive ratchet into tensioner and rotate down slipping belt over idler

Dec 21, 2008 | 2004 Chevrolet Tahoe

Not finding what you are looking for?
2000 Ford Focus Logo

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

71856 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...