Question about 1987 Nissan Pulsar

1 Answer

Losing power when i floor it through out the gears almost like a chutter kinda like one of the cylinders is not firing correctly does not smoke and does have a high ticking noise !!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,672 Answers

Check the SPARK PLUGS, if its new u have to GAP the electrode! Check also the timing, go to ur nearest garage and have a TUNE UP! That ticking noise might be from the HIGH VOLTAGE that suppose to go to ur SPARK PLUG and leaking out to body ground, check also the distributor cap and hi-tension cable wire! Hope that might help u out! Taah!

Posted on Nov 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tractor has been stood, had new head gasket but smokes white smoke and loses power when warm. What is wrong with it.. Any ideas..


Run a radiator pressure test or test for carbon monoxide vapor in the radiator. You have a cracked head or block if the head gasket was installed correctly. Note the installation would include measuring the block and head for warp.

Aug 31, 2016 | Ford Cars & Trucks

1 Answer

92 buick lesabre 97000 miles, on slow acceleration, @ 40mph going into 4th gear there is a mild chutter, same @ 50mph going into OD mild chutter and when down shifting from OD to 4th. All is when slow...


This sounds like a vacuum leak prob. At low acceleration there isn't quite enough vacuum for smooth shift.. But romp on it and it creates a vacuum at the same rate as your gas is getting sucked.

Dec 23, 2011 | 1992 Buick LeSabre

1 Answer

1999 chrysler cirrus lose brake pedal after stop pedal go to floor then lose all brakes


NOT A DO IT YOURSELF THING!! Please do everyone a favor and have your vehicle professionally looked at. Sounds like a master cylinder, but when you can't stop, everyone is at risk. Kinda stops today, and mayby not at all next time. Please be safe!

Dec 18, 2010 | 1999 Chrysler Cirrus

1 Answer

Power loss and white smoke from a Mazda B 2200 4 cylinder truck. need plug firing diagram also


Remember that white smoke is water in the cylinders,you may have a blown head gasket,and as for the plug firing diagram,need you to explain beter.

Oct 23, 2010 | 1992 Mazda B-Series

1 Answer

I crunk my car and then the gears want go into gear. The clutch went all the way to the floor. What could be the problem?


If you have low miles its most likely the slave cylinder. Its kinda like a master brake cylinder but its a smaller unit that is used for the clutch. Make sure the reservoir is full as they can leak. If its full it may be shot. If its empty its also shot and is leaking. Fill it up if its empty just to see if the clutch works so so. If it gets better then repalce the slave cylinder.

Aug 30, 2009 | 2002 Saturn VUE

1 Answer

Floods out 5 times out of 10 when trying to start car. Have to wait an hr. before trying to start again..Also a lose of power when going up a hill. Blue smoke comes out the exhaust. Also It won't change...


Blue smoke is caused by engine oil entering the cylinder area and being burned along with the fuel air mixture. As with the white smoke, just a small drop of oil leaking into the cylinder can produce blue smoke out the tailpipe. Blue smoke is more likely in older or higher mileage vehicles than newer cars with fewer miles. How did the engine oil get inside the cylinder in the first place? The car has many seals, gaskets, and O-rings that are designed to keep the engine oil from entering the cylinder, and one of them has failed. If too much oil leaks into the cylinder and fouls the spark plug, it will cause a misfire (engine miss) in that cylinder, and the spark plug will have to be replaced or cleaned of the oil. Using thicker weight engine oil or an oil additive designed to reduce oil leaks might help reduce the amount of oil leaking into the cylinder.

Jul 06, 2009 | 1991 Eagle Summit

2 Answers

1990 5 speed Honda Accord DX 2 cylinders wont fire


Could be head gasket or piston rings. Piston ring issues will smoke under load or when revving the engine.

Do a compression test.

Feb 27, 2009 | 1991 Honda Accord

1 Answer

Head gasket/ timing etc


Not 100% sure on that engine, but I'd be looking at my timing chain & gears, especially if gears have nylon teeth. Pull covers & have a look at condition & positioning for correct. Other thing I'd check is distributor & especially gear at end of shaft. If metal gear at bottom, you should be o.k.,but if nylon,could have melted.heated & distorted or broke. Be sure to mark it for re-install & don't crank engine before re-install.

Feb 23, 2009 | 2000 Pontiac Grand Am GT

2 Answers

B4 blowing plooms of smoke


Assuming that the Smoke is White or Black, You are gonna have to get an Overhaul on that Motor.

Jan 04, 2009 | 2000 Subaru Legacy

1 Answer

My jag xj sport v8 3.2 will not start


give the battery a full charge....un clip the air filter housing and leave it resting in place, put your foot to the floor on the gas pedal and keep cranking til it starts up,dont release the ignition key til it fires up,it will pop and bang and then when it fires up will smoke for a little bit (couple of mins) and then it will be fine.
If that doesnt work you will have to remove all 8 plugs,clean them,pour about 2 teaspoons in each cylinder before replacing plugs then do the same as above.
What happens with these engines is the cylinders get a bit too much fuel in them and it washes the oil away down the bores thus losing comression so it wont start.Instead of starting it up and switching it off briefly,let it run a bit and then give it a little rev before switching off...hope this helps

Dec 03, 2008 | 2006 Jaguar S-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...