Question about 2004 Renault 181

1 Answer

The heater fan on my senic 04 plate has stopped working on number 2 speed all the others work fine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Renault Master
  • 5,763 Answers

This is one of two things, first the switch may be bad or the most common would be the blower resistor, the resistor is what controls the blower speeds and go bad often, this is the most common part to fail when the blower stops working or some of the speeds dont work, hope this helps.

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced heater core. fan worked fine for 2 weeks now i have no fan speeds


It sounds line the Blower Motor Resistor, use Part Number: 5291-07017894 from Dorman as a reference.

Mar 02, 2014 | 1998 Ford F150 Regular Cab

1 Answer

Peugeot partner van 2001 heater won't workany clues


Comon for fans to die on Peugeots of this age,check fan speeds with everything else off. Otherwise an air block stopping water getting to heater. Bleed water system

Jan 21, 2014 | 1989 Peugeot 405

1 Answer

OUR 04 TRAILBLAZER, THE A/C STOPPED WORKING, IT WOULD WORK SOMETIMES AND BLOW COLD AIR NOW NOTHING COMES OUT, OR THE HEATER TOO.. LITTLE AIR WILL PULL THROUGH IF ON THE HIGHWAY, I CAN HEAR IT CLICK OVER...


a couple of things,1 blower motor fuse.2 blower motor gone out.3 switch on fan speed control switch not sending signal to fans.after checking the fuses.next check theswitch on control panel.set ac or heater.if fan still doesnt come on then replace it.when it work and then stops working there are a lot of possiblities that caused the prob relay too not fliping over inside staying close loop.hope this helps.

Aug 16, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

2001 Jeep Wrangler heater blower stopped working


Yes I would go with the switch, BUT, does it have a resistor bank? That is, how does it reduce the speed? Many systems use resistors to lower the speed. Burnt or bad connections can cause this as well.
You can test the blower motor by connecting direct power from a source like the cigarette lighter if you are handy.
Most of the time the lower speeds konk out but the high speed continues to work this is the resistor bank that goes out.

Mar 25, 2010 | 2001 Jeep Wrangler

1 Answer

My 2000 Mazda MPV heater fan works for 4 not for 1


You need to replace the blower motor resistor,it's in the heater box.Number 4 bypasses the resistor and all the other speeds go through it so it's the most likely problem.

Feb 19, 2010 | 2000 Mazda MPV

2 Answers

I have a 1999 Jeep Wrangler and the heater fan stopped working for all the fan speeds. The fuses are fine. How do you know if it is the blower resistor or the blower motor?


If you bypass the resistor pack and connect the motor directly to the fused 12v supply then the fan should run at maximum speed. If so, it's the resistor pack that's blown: a very common fault on a huge number of makes and models.

Feb 13, 2010 | 1999 Jeep Wrangler

2 Answers

2005 G6


If the heater fan on your car only works on "High" the problem is more than likely the resister assembly in your blower circuit or poor connections at the resister assembly. When the switch is in the "high" position the current does not flow through the resister assembly it flows directly to the coil of the blower relay. When the switch is in "low", "medium 1", or "medium 2" position the current flows through 1, 2, or all 3 of the resistors in the resistor assembly which results in the 3 different lower speeds. Check the resister assembly and replace if needed. 

Nov 25, 2008 | 2006 Pontiac G6

2 Answers

Heat when the fan blow at 2 but cold if the fan is at 3 speed


1st make sure the heated core is getting hot, do this by feeling the hoses under the hood that supply hot coolant to the core, if the inlet and outlet are hot then the core has circulation and is not the problem, check this and let me know what you find.

Nov 17, 2008 | 2004 Ford Explorer

1 Answer

Heater fan runs intermittently.


too simple .....3tings the motor bruchs when gets hot loose contact to the rotor and the fan stop working solution ; change the motor 2 the speed regulator mouted on the fan case is ba d change it 3 the heater suitch chek it too nicolas......

Oct 25, 2008 | 2003 Nissan Maxima

Not finding what you are looking for?

Open Questions:

See all 2004 Renault 181 Questions

Cars & Trucks Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

xxxxxx xxx

Level 3 Expert

4869 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...