Question about 1993 Oldsmobile Cutlass Supreme

1 Answer

What side of the block is the crankshaft positioning sensor located on a 1993 olds cutlas supreme?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,826 Answers

What side of the block is the crankshaft - prev.gif next.gif REMOVAL & INSTALLATION Fig. 1: Crankshaft Position (CKP) sensor mounting 88004g85.gif
Fig. 2: The 24X CKP sensor is mounted to the engine front cover - 3.1L (VIN M) engine 88004g89.gif
2.2L, 2.3L, 3.1L (VIN T and V) and 1991-93 3.4L Engines

  1. Disconnect the negative battery cable.
  2. Detach the sensor harness connector from the sensor.
  3. Unfasten the sensor retaining bolts, then remove the sensor from the engine.
  4. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  5. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  6. Install the sensor retaining bolt. Tighten to 88 inch lbs. (10 Nm).
  7. Attach the sensor harness connector.
  8. Connect the negative battery cable.
2.5L Engine
  1. Disconnect the negative battery cable.
  2. Remove the DIS assembly, as outlined in Section 2 of this manual.
  3. Remove the sensor retaining screws and remove the sensor from DIS assembly.
  4. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  5. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor.
  6. Fit the sensor to the DIS assembly and install the retaining screws. Tighten the retaining screws to 20 inch lbs. (2.3 Nm).
  7. Install the DIS assembly to the engine, as outlined in Section 2 of this manual.
  8. Connect the negative battery cable.
3.1L (VIN M) Engines 3X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Turn the steering wheel to the full left position.
  3. Raise and safely support the vehicle.
  4. Detach the sensor harness connector from the sensor.
  5. Unfasten the sensor retaining bolts, then remove the sensor from the engine.
  6. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  7. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  8. Install the sensor retaining bolt. Tighten to 71 inch lbs. (8 Nm).
  9. Attach the sensor harness connector.
  10. Carefully lower the vehicle.
  11. Turn the steering wheel to the straight ahead position, then connect the negative battery cable.
24X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. If necessary for access, remove the right front wheel and inner fender access cover.
  5. Unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 24420-B.
  6. Detach the sensor electrical connector.
  7. Unfasten the sensor retaining bolts, then remove the sensor from the vehicle. To install:
  8. Install the CKP sensor and secure using the retaining bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  9. Attach the sensor electrical connector.
  10. Install the balancer on the crankshaft using special tool J 29113, or equivalent.
  11. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  12. If removed, install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  13. Carefully lower the vehicle.
  14. Install the serpentine belt.
  15. Connect the negative battery cable.
1994-96 3.4L Engine 3X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the intermediate exhaust pipe.
  4. Remove the rack and pinion heat shield.
  5. Remove the alternator cooling duct.
  6. Detach the sensor electric connector.
  7. Remove the 3X CKP sensor from the engine.
  8. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  9. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  10. Install the sensor-to-block bolt and tighten to 71 inch lbs. (8 Nm).
  11. Attach the sensor connector.
  12. Install the alternator cooling duct.
  13. Install the rack and pinion heat shield.
  14. Install the intermediate exhaust pipe.
  15. Connect the negative battery cable.
24X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 38197, or equivalent.
  6. Detach the sensor electrical connector.
  7. Unfasten the sensor retaining bolts, then remove the sensor from the vehicle. To install:
  8. Install the CKP sensor and secure using the retaining bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  9. Attach the sensor electrical connector.
  10. Install the balancer on the crankshaft.
  11. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  12. If removed, install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  13. Carefully lower the vehicle.
  14. Install the serpentine belt.
  15. Connect the negative battery cable.
3.8L Engine
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Using a 28mm socket, unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 38197, or equivalent.
  6. Remove the CKP sensor shield. Do NOT use a prybar to remove the shield!
  7. Detach the sensor electrical connector.
  8. Unfasten the sensor retaining bolts, then remove the sensor from the block face. To install:
  9. Position the CKP sensor to the block face, then secure using the retaining bolts. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  10. Install the CKP sensor shield.
  11. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm), plus an additional 76°turn.
  14. Install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. CoWhat side of the block is the crankshaft - prev.gife negative battery cable.
prev.gif next.gif

Posted on Nov 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 olds 3.1 crankshaft position sensor location


should be on backside of motor in the middle of the block - above right side cv axle coming out of transmission

Jun 13, 2014 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Where is the 90 Cutlass Supreme crankshaft sensor located


Wasn't sure which engine you had so here's a picture for both the 4 and 6 cylinder. I hope this helps.

12_19_2011_11_57_30_pm.jpg

12_19_2011_11_57_51_pm.jpg

Dec 19, 2011 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Crank shaft sensor location on 1987 2.8 cutlas cierra


On the 2.8L V6 engine the crankshaft position sensor is on the side of the engine nearest the firewall and just above the pan rail in about the center of the block.
You will need to access from under the car.

Oct 28, 2011 | Cars & Trucks

1 Answer

1993 cadillac brougham fleetwood. how do you change the pickup coil?


REMOVAL & INSTALLATION -
  1. Disconnect the wiring harness from the Crankshaft Position (CKP) sensor.
  2. Remove the fastening bolt for the CKP sensor.
  3. Remove the CKP sensor and the O-ring seal from the engine block. To install:
  4. Thoroughly clean the mating surfaces of the CKP sensor and the engine bock.
  5. Install the CKP sensor with a new O-ring seal, into the engine block.
  6. Install he fastening bolt for the CKP sensor
  7. Attach the wiring harness to the CKP sensor. Be sure to route the cable correctly Fig. 1: The location of the Crankshaft Position Sensor (CKP) - 3.0L engine 91044g04.gif
    Fig. 2: Location of the CKP sensor connector - 3.0L engine 91044g05.gif
prev.gif next.gif

Nov 05, 2010 | 1993 Cadillac Fleetwood

1 Answer

My 1993 cutlas supreme stalls randomly while idling or driving , but restart right away


You will need to change the crank position sensor first and see if it corrects the problem. It is located behind the engine near the firewall. It's a bit tricky to get to it, you would need to rotate the engine forward then look under the exhaust manifold and under the cylinder closest to the drivers side. Use a 10 mm deep socket to loosen bolt. After replacement and it is still stalling then you will need to replace the ECM (vehicle computer). If it turns out to be the computer, go to your local junkyard to get an inexpensive replacement Click on the link below to view the CPS, it is around $22

http://www.partstrain.com/store/?N=0&Nr=AND(make:Oldsmobile,model:Cutlass+Supreme,year:1993,brand:Delphi,part:Crank+Position+Sensor)&ptc=S1171391678W45d204bec356b&ptid=ptc45891f6tnywz&id=Olqtv7cphi





Olds-Cutlass-Ciera.htm">http://en.allexperts.com/q/Oldsmobile-Buick-Repair-826/f/1992-Olds-Cutlass-Ciera.htm

Apr 12, 2010 | 1993 Oldsmobile Cutlass Supreme

3 Answers

Cant find crankshaft sensor location on my 1993 pontac grand prix 3.1 v6


front bottom of engine. It's wires connect to module and module is attached to coil packs.

Sep 04, 2009 | 1993 Pontiac Grand Prix

2 Answers

93 olds cutlas supreme overheating but there is no steam. Where is the fan temperature sensor located?


Usually near the thermostat.
By the way, remove the thermostat and drive around with the car. If it still overheats, might have some other problem, like you said, temp sensor, or some kind of electrical problem.

Jul 14, 2009 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Where is the camshaft position sensor located? I have a 93 Cutlass Supreme, I've replaced the fuel filter, fuel pump, and crankshaft sensor. It will not start. It ran briefly, but died and will not start...


it is located at rear of engine neer the firewall you will need to rotate the engine forward under the cylander closest to the drivers side it takes a 10 mm socet to remove it and its a little tricky

Mar 13, 2009 | 1993 Oldsmobile Cutlass Supreme

1 Answer

1898 olds cutlas supreme inernational


It is under the hood in the power distribution box

Oct 25, 2008 | 1993 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1993 Oldsmobile Cutlass Supreme Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...