Question about 1995 Buick Roadmaster

1 Answer

How to replace plug wires - 1995 Buick Roadmaster

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 277 Answers

Purchase a good set of wires do not settle for a cheapo set , lay out the wires and find the different sizes .
Pull one wire off and match the size to the new one , then reinstall the new one DO NOT pull them all off one at a time .
some might be tough to get off the spark plug so have a channel lock pliers ready...

Its that easy ..
Good Luck

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a cylinder 6 misfire on my 00 cadillac deville. do u think the plugs need to ne replaced?


Usually, if you only have 1 cylinder misfiring, you have either a bad spark plug or bad spark plug wire. If you replace the cylinder 6 spark plug and still have a misfire condition, replace your spark plug wires. If replacing the plug and wires doesn't fix the problem, replace the ignition coil.

Aug 03, 2011 | 2000 Cadillac DeVille

Tip

How to Test Spark Plugs in Audi A6 car?


1) Test the spark plug ignition. For that disconnect the spark plug wire from the spark plug.
2) Then touch the spark plug wire close to a metal surface of the car. Then spin the key in ignition switch. If you will see a spark or hear a crackling noise. This means the wire to the spark plug has voltage in it.
3) If there is no spark when you crack the engine it means that a spark plug wire is dead.
4) Check out all the battery cable, ignition wires and coil wires are hooked up properly to their points.
5) If any of the battery cable, ignition wires and coil wires is loose then this can also relate to no spark.
6) But if all the battery cable, ignition wires and coil wires are properly connected then its time to replace the spark plugs.
7) Before replacing clean the old spark plugs connections and recheck.
8) Many a time’s cleaning or moving the spark plug connections makes it work.
9) If nothing is getting the spark plug to spark, then it needs replacement.
This will help. Thanks.

on Mar 15, 2010 | Audi A6 Cars & Trucks

Tip

How to Test Spark Plugs in car?


The procedure is as follows:--
1)Test the spark plug ignition. For that disconnect the spark plug wire from the spark plug.
2)Then touch the spark plug wire close to a metal surface of the car. Then spin the key in ignition switch. If you will see a spark or hear a crackling noise. This means the wire to the spark plug has voltage in it.
3)If there is no spark when you crack the engine it means that a spark plug wire is dead.
4)Check out all the battery cable, ignition wires and coil wires are hooked up properly to their points.
5)If any of the battery cable, ignition wires and coil wires is loose then this can also relate to no spark.
6)But if all the battery cable, ignition wires and coil wires are properly connected then its time to replace the spark plugs.
7)Before replacing clean the old spark plugs connections and recheck.
8)Many a time’s cleaning or moving the spark plug connections makes it work.
9)If nothing is getting the spark plug to spark, then it needs replacement.
This will help. Thanks.

on Mar 15, 2010 | Audi A4 Cars & Trucks

2 Answers

Cylender number 1 misfire,


Do a complete tune up.. Spark plugs, wires, distributor cap, and rotor button... If it has coil packs that sit on top of the spark plugs.. Replace the spark plugs and cylinder number one coil

Feb 15, 2011 | 1998 Nissan 200SX

1 Answer

HOw to replace spark plug wires on a 1998 Mitsubishi montero sport?


Installing New Spark Plug Wires Is Simple, Especially Of One Wire Is Replaced At A Time. Compare The Length Of The Old Wire With The Length Of The New Wire. Replace Each Wire With One Of Equal Length.Make Sure The New Wire Is Fully Attached On The Plug And In The Distributor Or Coil Module.

Spark Plug Wire Replacement Is More Complicated If All The Wires Are Removed At Once.Then You Must Use The Engine Firing Order And Cylinder Numbers To Route Each Wire Correctly.

Apr 09, 2010 | 1998 Mitsubishi Montero Sport

2 Answers

Replace spark plugs and wires


ive found easiest access is to lower inner fender walls and change plugs from there

Nov 07, 2009 | 2000 GMC Yukon XL

1 Answer

NEW PLUGS AND WIRES


The correct arrangement?

I always remove one plug wire, replace that spark plug, and then replace that one spark plug wire. This way I never cross which plug wire to which position.

Oct 29, 2009 | 1999 Volkswagen Jetta

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

Spark Plug Wire Replacement


the easiest option is to unplug one wire and change that plug, then put the new wire on, repeat for all plugs and wires.

May 08, 2009 | Chevrolet Silverado 1500 Cars & Trucks

Not finding what you are looking for?
1995 Buick Roadmaster Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...