Question about 1997 Cadillac DeVille

1 Answer

My right and left turn signals do not operate. They show the arrow in the dash display but do not blink for the turn.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 6,826 Answers

Check the flasher and the bulbs.

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

2 Answers

69 turn signal problem left turn signal not working. right turn signal causes both to falsh


it's the grounds if they're both flashing fast it's definitely grounds take a test light and see if its got power goes through the test light grounded to the frame and if the light comes on then it's definitely your grounds

Jul 29, 2014 | 1969 Pontiac Firebird

1 Answer

Turn signals not working flasher fine


I would replace/check the dashboard bulb first.

Jun 04, 2017 | Chevrolet El Camino Cars & Trucks

1 Answer

Turn signals do not work


This is one FLASHER fault; ?m referring to the blinker "flasher fuse", it is the bottom round fuse under the dash in the fuse block.

REPLACEMENTThe turn signal flasher and hazard units are usually located located under the dash either to the left or right of the steering column on most models.
  1. Remove the turn signal flasher unit or hazard unit by pulling them up from the electrical connection.
  2. To install, push the unit(s) into the electrical connector

Good luck (remember comment and rated this).

Apr 10, 2010 | 1989 Jeep Comanche

1 Answer

Brake light, reverse light and turn signal issues


Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Jan 28, 2010 | 2003 Ford Windstar

2 Answers

I have a 2005 Chevy Colorado. The right rear passenger tail light will not come on, I have changed bulbs, and I have changed the entire lense assembly.Everytime you put your foot on the brake the right...


I have this exact same issue with my 05 Colorado and its so annyoying (not to mention unsafe)... I thought it was just the blub- becuase in my case my signal is no loger blinking. My break light still works, as does my parking light...

Any thoughts as to why this is happening?

Please HELP!!!

Dec 08, 2009 | 2005 Chevrolet Colorado

1 Answer

Right Turn Signal acts like the Emergency Flasher.


If you have an aftermarket trailer plug on your truck, you are going to want to inspect the wiring to the plug, and the connections in the plug. I think it's shorting out.

Jun 18, 2009 | Chevrolet Silverado 3500HD Cars & Trucks

Not finding what you are looking for?
1997 Cadillac DeVille Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...