Question about Dodge Ram 2500

1 Answer

Will start every time but will not accelerate

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,826 Answers

Check for a broken accelerator cable if the accelerator doesn't cause an rpm increase on the engine.

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 mazda 5


check that you fitted the accelerator cable correctly or connected up the electronic accelerator motor cable to the manifold throttle.

Apr 12, 2014 | 2006 Mazda 5 2.0

Tip

How to reset ECU,Throttle and Accelerator Position Learning


Hi.

Below the procedure to reset ECU,Throttle and to perform Accelerator Position Learning on Nissan. It works on Titan, Altima, Infinity, pathfinder and other models.

ECU Resetting


While performing the procedures below, ensue that you are respecting the times stated. If the steps are not done within the specified times, the module will not reset. You will need to use a watch or a chronograph while performing the procedures.

Procedure:

1. Ensure that the accelerator pedal is fully released, set ignition switch to the “ON” position, then wait 3 seconds.
2. Follow the steps a and b below, repeat the two steps in sequence quickly for five times within 5 seconds.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal in full.
3. Wait 7 seconds, then depress the accelerator pedal completely, and hold it for about 10 seconds until the CEL (check engine light) starts blinking.
4. Release the accelerator pedal while the CEL is still blinking.
5. Wait 10 second.
6. Depressthe accelerator pedal in full and hold it for 10 seconds or more.
7. Fully release the accelerator pedal while the CEL light keeps flashing.
8. Turn the ignition switch to “OFF” position and start the vehicle. If procedure has been done correctly, then the light light will turn off.
If the light continues to stay on, repeat the procedure.

Accelerator Pedal Release Position Learning

Procedure

1. Ensure that the accelerator pedal is completely released before starting the procedure.
2. Turn the ignition switch “ON” and wait at least 2 seconds.
3. Turn the ignition switch “OFF”, and wait at least 10 seconds.
4. Turn the ignition switch “ON” and wait 2 seconds.
5. Turn the ignition switch “OFF” and wait 10 seconds.

Throttle Valve Closed Position Learning

Procedure

1. Ensure that accelerator pedal is completely released.
2. Turn ignition switch to the “ON” position.
3. Turn ignition switch to the “OFF” position and wait at least 10 seconds.
Ensure that the throttle valve moves after turning the switch off.

Idle Air Volume Learning (Throttle Position Learning)

Procedure

1. Follow the Accelerator Pedal Released Position Learning described above.
2. Do the Throttle Valve Closed Position Learning also described above.
3. Start the engine, and allow warming up.
4. Turn the ignition on “OFF” positionand wait 10 seconds.
5. Ensure that accelerator pedal is fully released, then turn the ignition switch to “ON” position, and wait 3 seconds.
6. Repeat the steps a and b below five times within 5 seconds in sequence.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal until reaching full extension.
8. Wait 7 seconds or more, depress the accelerator pedal completely and hold the pedal down for about 20 seconds until you see that the Check Engine Light stops blinking and starts getting steady..
9. Rrelease completely the accelerator pedal within 3 seconds after the light coming ON.
10. Start engine and let it run at idle for about 20 seconds.
12. Test the engine to ensure the idle speed and ignition timing are set correctly.

Regards.

on Mar 25, 2010 | Nissan Titan Cars & Trucks

1 Answer

2012 ford focus acceleration takes awhile


Can i ask you when the last time this car was serviced or how many k's or miles it has done?

Jan 26, 2014 | 2012 Ford Focus S Sedan 2.0L 4-cyl....

1 Answer

1993 Mustang 2.3L Trouhble(again); It's slugish at accelerating from a stop(some times falling on its face and dieing), jerks at highspeeds when trying to accelerate, and has hard starts. Any help


All the above problems were happening to my truck, and the engine light never did come on. Finally changed the O2 sensor, and it runs like new again.

Mar 30, 2013 | Cars & Trucks

1 Answer

I have a Fiat Bravo when i accelerate it jerks off it does that when i accelerate hard


have you tried altering the timing on the engine after you changed the timing belt?

Nov 19, 2012 | 2007 Fiat Bravo 1.4

1 Answer

Car will not accelerate properly


timing issues?? or transmission problems maybe??

Mar 11, 2012 | 2001 Mitsubishi Eclipse

1 Answer

1991 pontiac 6000 6 cyl stalls on acceleration This situation varies, sometimes it stall when your just barely starting to accelerate and other time I can accelerate a lot more with no problem unless I...


Sounds like the engine is starving for fuel - plugged fuel filter, failing fuel pump, malfunctioning fuel regulator, etc. Have the fuel pressure checked.

Jul 03, 2017 | 1991 Pontiac 6000

1 Answer

Just purchased 2000 Buick LeSabre. 56,000 miles, sporadic trouble starting--sometimes starts first try, other times will crank and won't start and have to slightly depress the accelerator and then will...


If it runs rough all the time, could be a bad coil pack/wires. If just starting and hesitates on acceleration, I would suspect the throttle position sensor.

Jun 10, 2011 | Buick LeSabre Cars & Trucks

1 Answer

Couldn't accelerate brakes stiff and won't start now


Jumped timing
timing belt water pump timing chain approx 600 dealer est.

Jun 07, 2010 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...