Question about 1998 Ford Contour

1 Answer

There is a loud blender sound when the car is running

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Sounds like you have a hole in your exhaust pipe close to motor inspect manifolds for rust/ rot holes

Posted on Nov 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 envoy, passenger side blows out hot air when ac is on. driver side is ok & coolant level is fine


your blender door on one side may be stuck when you start with the a/c on the door should make a loud tud sound

May 04, 2017 | AC Cars & Trucks

1 Answer

Is it normal for my 2012 subaru outback to have a loud popping/clunking sound after I am done driving it (shut the car off)? I Have heard it from my previous car as a cooling thing but this seems loud


run the fault codes as it may be an indication that the cat converter is running at an excessive temperature due to incorrect air/fuel mixture settings from the ECM

Sep 12, 2014 | 2012 Subaru Outback 2.5i Wagon 2.5L 4-cyl....

3 Answers

No heat in the front of my 2001 ford windstar blows hard but cold. back heater works fine


are you sure the dial is adjusting? pull the dial off, look inside of it, the plastics inside might be cracked

Dec 06, 2009 | 2001 Ford Windstar

1 Answer

My auto isn't switching from A/C to heater. Someone said it might be the blender motor. What do you think?


First check to see if the compressor is turning. (It will probably cycle on and off. It should stay on ROUGHLY as much as it is off when it has run some; at first it should run and not cycle off for the first minute or so.) If it doesn't cycle as explained or if nothing but the pulley turns and not the front clutch face, have that fixed. The operation of the blender door is evident when the fan is on high, and you set it from hot to cold - you'll be able to hear that the sound of the air rushing through the ducting makes a different sound at each extreme of hot and cold. Check for that. If you can't hear any difference and your compressor is working well, have your blender looked at.

Dec 02, 2009 | 1999 Chrysler 300M

1 Answer

Loud noise from under the dash, ac/heater area. No cool air 97 li


If this noise is a clicking sound and is coming from the front center of the dash, then it may be the blender door motor which will require removal of the dash to replace it. It will keep the door from switching from heat to a/c. Does the odor smell like you have a freon leak in your a/c evaporator core or does it smell like a rat stuck in your heater and a/c ducts?

Aug 01, 2009 | 1997 Lincoln Town Car

1 Answer

93 MX6 throttle body is Popping, loud,sounds like a diesel


Sounds like the pipe/connection from the exhaust manifold to the EGR valve that is located at or near the throttle body has a leak. That would make a loud popping noise.

Jul 15, 2009 | Maybach 62 Cars & Trucks

1 Answer

02 Durango: loud engine/exhaust sound. Also


Keep an eye on the coolant level, you might have a cracked engine block!!!
Watch for steam around Motor Block once the engine gets warm.

Jul 14, 2009 | 1997 Oldsmobile Aurora

1 Answer

1999 MAZDA MILENIA MAKES LOUD NOISE WHEN KEY IS TURNED OFF


Could be the crank shaft. Had the same thing happen to me... kinda sounds like a spoon in the blender? Looking at $400 for part and labor if nothing else has been damaged. But if the crank shaft goes, your looking at another $20 for the belt too. Not too bad. Shouldn't keep letting it do that, eventually it'll snap off completely and your car won't go anywhere.

Feb 10, 2009 | 2001 Mazda Millenia

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...