Question about 2007 Dodge Nitro R/T New Cars

1 Answer

2007 dodge nitro, malfunction indicator light came on while in an automatic car wash, while engine was running. Car only has 8,000 miles on it. thanks!

Posted by on

  • robzillanato Nov 12, 2010

    Thank you for your response ZX2Fast! No code comes up with the scan at all? I did notice that my fluid level on my radiator is almost to the minimum line, wondering if that could be it? MIL light is still on this morning, and vehicle seems to run fine. Any other suggestions would be greatly appreciated! Thanks, Rob

  • robzillanato Nov 28, 2010

    Never did find out why the MIL light came on? It went off a day or two later. Thinking maybe something got wet in the automatic car wash, car is running fine now. Thanks again for your help ZX2Fast!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 547 Answers

There are literally thousands of codes that can cause that light to come on. Auto Zone will scan the computer for free and give you any codes you have. We would need to know the codes to help you pinpoint the issue.

Posted on Nov 12, 2010

Testimonial: "ZX2Fast had the answer I needed, and told me where I could have my MIL indicator light checked for free, rather than paying the Dealer to check it! "

  • 2 more comments 
  • Brad Kirby
    Brad Kirby Nov 12, 2010

    Some of the cheaper scanners can't pull manufacturer specific codes. You might have to have a shop or someone you know with an Xcal device with a Dodge tune pull the code for you.

  • Brad Kirby
    Brad Kirby Nov 13, 2010

    The overflow bottle doesn't always accurately reflect actual coolant level. If your level is low that could set a special code that turns your MIL on but isn't readable by any scanner that isn't loaded with Dodge specific codes.

  • robzillanato Nov 13, 2010

    Thanks again ZX2Fast, I will bring my car to the dealer and have them scan it. Strangely enough tonight the light just turned off. I appreciate all your help with this problem!!

  • Brad Kirby
    Brad Kirby Nov 27, 2010

    You are welcome. Did you find out what the problem is?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DODGE NITRO 4 LITRE EGR LOCATION 2007


The metal tube from the intake going behind the engine is going to the EGR Valve.


http://www.allpar.com/images/engines/4-V6-2.jpg

Apr 14, 2015 | 2007 Dodge Nitro

1 Answer

Gas cap indicator light stuck on; gas cap is on-checked it ten times. 2007 Nitro, about 40,000 miles


Hello,
There are a number of things that the computer system will reset automaticly, but, it usually requires 2 drive cycles.

A drive cycle includes, accelerating, highway speed, local speed, stopping. If you have already done that, you may try to reset by removing the ground cable, ( black wire ), from the battery for a minute or so.

I hope this helps you.

Feb 16, 2011 | 2007 Dodge Nitro R/T New Cars

1 Answer

My 2007 dodge nitro has an error code "no bus" how do i fix it?


well :no bus: means that the infomation panell is not getting a signal check the harness below the odometer. I guess the car is running fine, if not then its the ecu itself.

Oct 01, 2010 | 2007 Dodge Nitro R/T New Cars

1 Answer

2007 DODGE MAGNUM /CHECK ENGINE LIGHT ON INTERMEDIATLY WHEN ON CAR RUNS ROUGH WHEN LIGHT GOES OUT WILL GO BACK TO NORMAL CODE FROM ECM INDICATES HIGH VOLTAGE FROM EGR POSITION SENSOR


In order to fix yours problem with EGR system, you must remove and clean inside the EGR valve. Refit all in reverse order. Therefore you can erase ECM memory from faults. After these operations you can run on higway for few miles for engine warm up and exhaust system cleaning!

Jan 11, 2010 | Dodge Magnum Cars & Trucks

1 Answer

Check engine light on diagnostics say rpm's too


That would be your rev limiter or your map sensor.

Sep 01, 2009 | 2007 Dodge Nitro R/T New Cars

1 Answer

Service intervals on a 2007 dodge nitro


tune at 100,000 miles, filters at 30,000, tranny service is 60,000 and 30,000 for heavy use, like towing.

Feb 23, 2009 | 2007 Dodge Nitro R/T New Cars

2 Answers

2007 Dodge Nitro Tail Light Replacement


look at the car manual under maintenance and then rear light bulb replacement. First take out the two hole covers using a flat head to loosen then wiggle and turn by hand to get out. Pull the light unit straight back, and unplug the electrical. Don't break anything.
Then use a star driver (check your misc socket set drivers for the right size). Unscrew the two star head screws and pull this bulb holder straight off the tail light (same direction as screws). Replace the bulb and put back together in reverse.

Nov 04, 2008 | 2007 Dodge Nitro R/T New Cars

Not finding what you are looking for?
2007 Dodge Nitro R/T New Cars Logo

1,782 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...