Question about 2004 Cadillac SRX

1 Answer

Tie rod end replace. outer end in steering knuckle. what does inner end connect to? it goes inside a boot

Posted by on

Ad

1 Answer

Connects to the steering rack

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace cv joints


Hi Douglas, I'm glad to help. My first suggestion is to get to complete shaft. This way you want have any problems later on. It's not that much more expensive and you'll be glad you did. Below is the procedure for replacing them.



FRONT DRIVESHAFTS

REMOVAL
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. Refer to Hoisting in the Lubrication And Maintenance section of this manual for the required lifting procedure to be used for this vehicle.
  2. Remove the cotter pin and nut lock Hub And Bearing To Stub Axle Retaining Nut from the end of the stub axle.
  3. Remove the wheel and tire assembly from the vehicle.
  4. Remove the wave washer Wave Washer from the end of the stub axle CAUTION: Wheel bearing damage will result if after loosening hub nut, vehicle is rolled on the ground or the weight of the vehicle is allowed to be supported by the tires.
  5. With the vehicle's brakes applied to keep hub from turning, loosen and remove the stub axle to hub nut.
  6. Remove the two front disc brake caliper to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts
  7. Remove the disc brake caliper from the steering knuckle. Caliper is removed by first rotating top of caliper away from steering knuckle and then removing bottom of caliper out from under machined abutment on steering knuckle Brake Caliper Mounting To Steering Knuckle
  8. Support disc brake caliper assembly by using a wire hook and suspending it from the strut assembly Correctly Supported Disc Brake Caliper Do not allow the brake caliper assembly to hang by the brake flex hose.
  9. Remove the brake rotor from the hub and bearing assembly Remove/Install Brake Rotor
  10. Remove nut attaching outer tie rod end to steering knuckle Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with a wrench.
  11. Remove tie rod end from steering knuckle using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle Arm
  12. Remove the steering knuckle to ball joint stud, clamping nut and bolt Control Arm To Steering Knuckle Attachment from the steering knuckle.
  13. Using a pry bar, separate steering knuckle from ball joint stud Separating Ball Joint Stud From Steering Knuckle Note: Use caution when separating ball joint stud from steering knuckle, so ball joint seal does not get cut. NOTE: Care must be taken not to separate the inner C/V joint during this operation. Do not allow driveshaft to hang by inner C/V joint after removing outer C/V Joint from the hub/bearing assembly in steering knuckle, end of driveshaft must be supported.
  14. Pull steering knuckle assembly out and away from the outer C/V joint of the driveshaft assembly Steering Knuckle Separation From Driveshaft
  15. Support the outer end of the driveshaft assembly. Insert a pry bar between inner tripod joint and transaxle case Disengaging Inner Tripod Joint From Transaxle Pry against inner tripod joint, until tripod joint retaining snap ring is disengaged from transaxle side gear.
  16. Hold inner tripod joint and interconnecting shaft of driveshaft assembly. Remove inner tripod joint from transaxle, by pulling it straight out of transaxle side gear and transaxle oil seal Tripod Joint Removal from Transaxle When removing tripod joint, do not let spline or snap ring drag across sealing lip of the transaxle to tripod joint oil seal.
INSTALLATION
  1. Thoroughly clean spline and oil seal sealing surface, on tripod joint. Lightly lubricate oil seal sealing surface on tripod joint with fresh clean transmission lubricant.
  2. Holding driveshaft assembly by tripod joint and interconnecting shaft, install tripod joint into transaxle side gear as far as possible by hand Tripod Joint Removal from Transaxle
  3. Grasp inner tripod joint an interconnecting shaft. Forcefully push the tripod joint into side gear of transaxle, until snap ring is engaged with transaxle side gear. Test that snap ring is fully engaged with side gear by attempting to remove tripod joint from transaxle by hand. If snap ring is fully engaged with side gear, tripod joint will not be removable by hand.
  4. Clean all debris and moisture out of steering knuckle, in the area were outer C/V joint will be installed into steering knuckle.
  5. Ensure that front of outer C/V joint which fits against the face of the hub and bearing is free of debris and moisture before installing outer C/V joint into hub and bearing assembly Outer C/V Joint Inspection
  6. Slide drive shaft back into front hub and bearing assembly. Then install steering knuckle onto the stud of the ball joint assembly Steering Knuckle Separation From Driveshaft
  7. Install a new steering knuckle to ball joint clamping bolt and nut Control Arm To Steering Knuckle Attachment Tighten the clamping bolt and nut to a torque of 135 N·m (100 ft. lbs.)
  8. Install tie rod end into steering knuckle. Start attaching nut onto stud of tie rod end. While holding stud of tie rod end stationary using a 11/32 socket, Removing Tie Rod End Attaching Nut tighten tie rod end to steering knuckle attaching nut. Then using a crowfoot and 11/32 socket Torquing Tie Rod End Attaching Nut , tighten the tie rod end attaching nut to a torque of 54 N·m (40 ft. lbs.)
  9. Install braking disc on hub and bearing assembly Remove/Install Brake Rotor
  10. Install disc brake caliper assembly on steering knuckle. Caliper is installed by first sliding bottom of caliper under abutment on steering knuckle, and then rotating top of caliper against top abutment Brake Caliper Mounting To Steering Knuckle
  11. Install disc brake caliper assembly to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts Tighten the disc brake caliper assembly attaching bolts to a torque of 22 N·m (195 in. lbs.)
  12. Clean all foreign matter from the threads of the outer C/V joint stub axle. Install the washer and stub axle to hub/bearing assembly nut on stub axle and securely tighten nut.
  13. Install front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)
  14. Lower vehicle.
  15. With the vehicle's brakes applied to keep hub from turning, tighten the hub nut to a torque of 244 N·m (180 ft. lbs.) Torquing Front Stub Axle To Hub Nut
  16. Install the spring wave washer on the end of the stub axle.
  17. Install the hub nut lock, and a new cotter pin Hub And Bearing To Stub Axle Retaining Nut Wrap cotter pin prongs tightly around the hub nut lock as shown in Hub And Bearing To Stub Axle Retaining Nut
  18. Check for correct fluid level in transaxle assembly. Refer to Group 21, Transaxle for the correct fluid level checking procedure for the type of transaxle being checked.
  19. Set front toe on vehicle to required specification.

May 07, 2014 | 2000 Dodge Caravan

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

How do i loosen the outer tie rod end to remove it from the bushing once tie rod is out of streeing knuckle i know it will need to be aligined and i need to count treads when putting new outer tie rod end...


You may need a propane torch to heat up the nut on end of outer tie rod. With tie rod still attached to steering knuckle try to loosen the outer tie rod end nut that is connected to inner tie rod. Pull tie rod end back out of knuckle. Use pliers or vise grips to hold inner tie rod end while turning outer tie rod end to the left.

Oct 27, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

2 Answers

One of the steering rods that goes from the rack to the right tie rod is bent. Can I replace the rod or must I replace the entire rack?


you can replace just the tie rod yourself although you do need a special tool but you should be able to get it at any parts store just take the outer tie rod loose from the steering knuckle remove the rubber boot from the inner tie rod and get the proper size tool to fit he nut and remove and replace the inner tie rod and install in reverse order make sure to count the amout of turns that removed the outer tie rod and reinstall the same amount of turns then afterward the car needs to be aligned

Apr 13, 2010 | 2000 Ford Focus

1 Answer

I can't seem to get any of my tools into this small space to loosen the inner tie rod. i have many tools but it seems like i need to take my whole engine and transmission assembly just to get to it. any...


You need an inner tie rod tool. Looks like a pipe with a drive socket on one end, and a reciever on the other. Unbolt the outer tie rod from the knuckle, and loosen the lock nut on the rod
3b87c80.jpg


Either use a puller to remove the outer end, or hit the knuckle with a hammer, and remove the outer end from the knuckle. Unscrew the outer from the inner rod (break the lock nut loose before removing the outer from the knuckle, or you will not be able to loosen it)


Remove the bellows from the rack and inner rod.
Use a drift or punch and a hammer to push the lock plate off the inner rod end


Place the correct adapter over the inner rod end, slide the rod inside the tool, and lock the reciever end of the tool on to the adapter. place a ratchet on the drive end of the tool, and remove the rod.

Good luck.

Mar 02, 2010 | Nissan Maxima Cars & Trucks

1 Answer

How too change inner tierod on 2005 pontiac g6


If you have electric steering(no power steering pump)you have to change the entire steering gear assembly as no part is available.If you have the system with a pump a part is available.In order to change the inner tie rod you would loosen the 21mm lock nut on the tie rod.remove the 18mm nut on the outer tie rod and spin off after removing the outer tie rod from the steering knuckle.Remove the nut and the inner and outer clamps on the tie rod boot.remove the boot.You would then need a special inner tie rod tool to turn the threaded inner rod from the steering gear.

Oct 17, 2009 | 2005 Pontiac G6

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

1 Answer

I need to replace the inner tie rods on my 97' conti......need a diagram of how to and any other info pertinent to the job - Bair


If this is a rack and pinion type steering, in order to remove the inner tie rods you will first have loosen the jam nut at the outer tie rod end,next unbolt the outer tie rod from the steering knuckle, unscrew the outer tie rod end off (be sure to count how many turns to remove), next remove the inner bellows boot (black boot) from the tie rod / rack and pinion, next is to unscrew the inner tie rod from the rack assembly (the do make a tool for this to make it easier) but if you do not have the tool,you can sometimes use a big pair of channel locks or a big enough wrench to fit on the fitting on the inside of the inner tie rod, and just unscrew the inner tie rod (normal left=loosen, right=tighten). Hope this helps. Would also recommend having it aligned after you are finished.

Mar 12, 2009 | 1997 Lincoln Continental

1 Answer

How do you replace the outer tie rods on 2000 oldsmobile alero


Jack up vehicle; back off set nut that connects outer to inner tie rod; remove cotter pin and castle nut from outer ball socket of t/r end; take a 'pickle fork' and tap between joint and steering knuckle to separate; then unscrew the outer t/r from the inner t/r, "counting the number of turns until completely off. Run the new locking nut onto new tir rod end; turn t/r same number of turns, and lock set nut; runt the new post of t/r end back into steering knuckle, tap down with a hammer, and use new castle nut to tighten; insert new cotter pin and grease fitting; again tighted locking nut to inner t/r; grease new t/r end...good to go!

Jan 31, 2009 | 2000 Oldsmobile Alero

Not finding what you are looking for?
2004 Cadillac SRX Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...