Question about 2007 Lexus RX 350 FWD

Open Question

How do you close the hood? - 2007 Lexus RX 350 FWD

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I open hood on Cadillac ATS


To open the hood:
1. Pull the hood release handle
inside the vehicle. It is on the
lower left side of the instrument
panel.
2. Go to the front of the vehicle and
move the secondary hood
release lever toward the right
side of the vehicle.
3. Lift the hood.
To close the hood:
Before closing the hood, be sure all
filler caps are on properly. Then,
bring the hood from full open to
within 152 mm (6 in) of the closed
position. Pause, then push the front
center of the hood with a swift, fi

Jun 07, 2015 | 2013 Cadillac ATS

3 Answers

How do I close a 1996 Hood on a TBird when it won't shut?


Close the latch with the hood open to make sure it works. If it does make sure the hood release handle,is in all the way and adjust the latch assembly

Jan 12, 2015 | 1996 Ford Thunderbird LX

3 Answers

The hood is hard to close


Sounds like your hood release locking mechanism is gummed up..it is the part on the car that the hood locking bar fits into..it also is attached to the hood release..have someone operated the hood release while you use a carb lineage spay on the hood release..keep doing it until the mechanism works smoothly..once that is done spray some WD40 on it..then from then add it to your service reminder to oil it up....good luck..

Nov 27, 2014 | 2000 Ford Explorer

1 Answer

Chevy Prizm Hood Is Stuck Closed


try pushing down on hood while somebody elss pull latch mau be stuck

Dec 06, 2013 | 1999 Chevrolet Prizm

1 Answer

Remove a hood from a 2006 nissan altima


absolutely not. first thing, carefully remove the washer hoses. there are four bolts on the hinges. just remove front two completely then slowly remove rear two while someone else holds the other side of hood. the hood itself is relatively light.when reinstalling, keep the hood bolts slightly loose and bring down the hood slowly, not letting it close. when you can position the hood straight, tighten a bolt on either side then close the hood. if it closes and opens while being evenly gapped on both sides tighten all four bolts. then replace the washer hose and done.

Nov 13, 2013 | Nissan Altima Cars & Trucks

1 Answer

Hood Release and Hood Lock


lube the hood latch on the car. im sure its dry. lube and work the lube in by closing/opening hood.

Jun 25, 2013 | Nissan Cars & Trucks

1 Answer

Trunk pop open when driving


close hood and lift up on hood to see if it stays closed.
if not, check inside car to see if latch(that you pull) is in the correct position. you can tell when hood is closed that there will be some tension on latch.
check under hood, where hood closes on latch of hood, is tight and secure(no loose bolts)
also check cable if broken.
only those things can cause hood to pop open.
if all visual inspections check out and still continues to open while driving then the latch (the mechanism that hold the hood down) is bad. vibrating while driving will cause it to open.

May 12, 2011 | Volkswagen Jetta Cars & Trucks

1 Answer

How do you change the cooling fan



Electric Engine Fan

Cooling Fan Connectors

Removal & Installation
2.2L& 2.4L Engines
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
  4. Remove the upper radiator mount bolts.
  5. Remove the upper two hood latch support bolts.
  6. Remove the two lower hood latch support bolts.
  7. Raise the vehicle.
  8. Remove the cooling fan mounting bolt.
  9. Disconnect the electrical connector from the cooling fan. Remove the cooling fan assembly.

To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
  3. Install the cooling fan mounting bolt. Tighten the bolt to 53 inch lbs. (6 Nm).
  4. Lower the vehicle.
  5. Install the lower two hood latch support bolts. Tighten the bolts to 20 ft. lbs. (27 Nm).
  6. Install the two upper hood latch support bolts. Tighten the two upper hood latch support bolts to 80 inch lbs. (9 Nm).
  7. Install the upper radiator mount bolts. Tighten bolts to 89 inch lbs. (10 Nm).
  8. Install the hood close out filler panel.
  9. Install the hood close out filler panel retainers.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
    CAUTION Be careful when you handle a sensor. Do not strike or jolt a sensor. Before applying power to a sensor:
    0e518e2.jpg

    Fig. Remove the hood close out filler retainers and the hood close out filler panel
    1. Remove any dirt, grease, etc. from the mounting surface
    2. Position the sensor horizontally on the mounting surface
    3. Point the arrow on the sensor toward the front of the vehicle
    4. Tighten all of the sensor fasteners and sensor bracket fasteners to the specified torque value.
  4. Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.
  5. Disable the air bag sensor.
  6. Remove the upper radiator mount bolts.
  7. Remove the upper 2 hood latch support bolts (2).
  8. Remove the 2 lower hood latch support bolts (4).
  9. Raise the vehicle.

    581eb59.jpg
    Fig. Remove the cooling fan mounting bolt
  10. Remove the cooling fan mounting bolt.
  11. Disconnect the electrical connector from the cooling fan.
  12. Remove the cooling fan assembly.
To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the cooling fan mounting bolt and tighten the bolt to 53 lb inches (6 Nm).
  4. Lower the vehicle.
  5. Install the lower 2 hood latch support bolts and tighten the bolts) to 20 ft. lbs. (27 Nm).
  6. Install the 2 upper hood latch support bolts and tighten the bolts to 80 lb inches (9 Nm).
  7. Install the upper radiator mount bolts and tighten bolts to 89 lb inches (10 Nm).
  8. Engage the air bag sensor.
  9. Install the hood close out filler panel.
  10. Install the hood close out filler panel retainers.
  11. Connect the negative battery cable.
Hope this help (remember comment and rated this).

Apr 14, 2010 | 2001 Chevrolet Cavalier

1 Answer

Hood will not close completely on 1996 Tahoe


Try "resetting" the lock. With the hood open-lube the lock good with wd-40 or similar and go pull the hood latch handle several times. See if it works good when your done. If not ,something may have got bent from closing attempts. Will have to look at adjustment then. Hope I helped. Thanks

Apr 06, 2009 | 1996 Chevrolet Tahoe

1 Answer

Attach hood prop rod 2001 Ford Focus


First you will need to get a hood prop bushing from pobably your Ford dealer or you can get one from a salvage yard. You may also need a hood rod attchment. In order to attach your hood rod on. In order to allow your hood to close without the rod interfering with the closing of your hood.This can either be obtained at your dealer or salvage yard. Then you will need a 4or 5 foot poll in order to prop your hood.So that you can place the bushing in and also hood attachment bushing.Both bushings snap right in. You will need to take your hood rod and place it in the hole of the bushing the hood rod should have a short bend at the bottom of it.Like an L or 7 the L shape should seat it self into the bushing.In order to erect the rod to hold the hood up.Or in order to attach it on the hood attachment.Before closing the hood. The hood rod bushing for extending your hood rod.In order to hold your hood up.Goes in the side of the inside frame of the body to the rear of the passenger side of the car again it just snaps in. And the hood rod attachment goes towards the front of the passenger side and it also snaps in.It's located horizontal of the headlight.The hood rod bushing is a 2 sided little round shaped plastic bushing just big enough for your hood rod to fit through.And it is usually white. And your hood rod attachmewnt is usually black.

Jul 31, 2008 | 2001 Ford Focus

Not finding what you are looking for?
2007 Lexus RX 350 FWD Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

905 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...