Question about 2007 Subaru Legacy 2.5i SE Sedan

Open Question

My 2007 subaru legacys rear window defrost quit working and i already checked the fuse and it looked fine. any other suggestions on troubleshooting.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 337 Answers

SOURCE: SUBARU LEGACY 94 S/W FUSE BOX

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800671f8

Posted on Dec 10, 2008

hondaman900
  • 40 Answers

SOURCE: !993 subaru legacy doors dont unlock

If it takes that much force to manually open the doors, and it's on the doors that are less used, then I'd bet it's a set of door locks and actuators in need of lubrication. 
Electric door lock actuators can easily be stopped or slowed down by resistance in the mechanism. This can be caused by corrosion, water getting into the door, and just old age and lack of use. I'd take the door panels off and take a peek. 
On the Legacy the panels pop off fairly easily. You'll need to pry them off carefully with a flat screwdriver. You'll feel where the fasteners are, where the panels are resisting coming off, and prise the panel gently and firmly at these points and they'll pop out. Once out you'll see the lock mechanism. 
Moving it by hand will tell if it's corroded or bound up. Apply some white litium grease to the mechanism, making sure to squirt/work it in, and then work the door handle/mechanism to get the lube into the linkage and actuators. Check the electrical contacts for corrosion while there and spray with WD-40 to protect them. This should free up the door mechanism and the actuators should then be able to do their job.
If after the above steps the electric actuators still don't work, use a voltmeter or circuit tester to check for 12V at the actuator when the door button is pressed. If you don't see any power, recheck that fuse and then the wiring back to the door harness. It's unlikely that this is the cause as its unlikely that you'd get only 3 out of 4 bad, but you never know in these old cars.
Hope this helps.

Posted on Dec 28, 2008

  • 1 Answer

SOURCE: subaru legacy fuse 1995

The fuse is only for when you are running a smaller sized spare tire. You have to put one in when you put the spare on to make the car FWD only. Go only far enough to get the tire replaced. Do not drive the car extended distances in FWD.

Posted on Mar 08, 2009

  • 2 Answers

SOURCE: 1999 Subaru legacy will not start

Check your terminal connections, if they are loose they will need to be inspected for breaks. If they are broken you will need to replace the connection. Make sure they are clean and free of corrosion.

Other possible Problems
If the car wont turn over your starter could be bad.
If it turns over but wont start it could be any number of these problems.
Coil Pack
Plug Wires
Spark Plugs
EBX (Engine Brain Box)
CBX (Chassis Brain Box)
Crank Sensor
Fuel Pump
Fuel Rail
Fuel Injector

Good luck

Posted on Feb 15, 2010

  • 7 Answers

SOURCE: 1990 Subaru Legacy power window switches not

check the power window control box

Posted on Mar 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keep blowing fuel pump fuse on 98 Subaru legacy outback changed the pump already


check fuel pump wiring underneath rear seat, they melt and might short out inside to earth.

Sep 30, 2014 | 1998 Subaru Legacy

1 Answer

97subaru legacy, and both the front and rear lighters aren't working, and would like to know which and whre the fuses are i need to change The location of the fuses


hi the fuses are located under the drivers side (jdm version) on the side of panel under a black plastic cover, just look for the blown one as the locations are all written in japenese

Apr 06, 2012 | 1997 Subaru Legacy

1 Answer

Rear windshield wiper quit working, can't find inside fuse box to check fuse.


Check the driver's side inside the car on the left. About where your left shin rests when driving. And if this is incorrect, did you check the owner's manual? take care and good luck.

Mar 06, 2011 | 1999 Subaru Legacy

1 Answer

Rear defrost not working on 2000 legacy gt, fuses are good, light comes on on switch. Any ideas?


If it is a wagon the wiring goes bad back at the gate. If not you need to check the voltage on both sides of the grid and work back till voltage is found.

Dec 08, 2009 | 2000 Subaru Legacy

2 Answers

2005 Subaru Legacy electrical repair question?


The #3 fuse does service both windows and door locks and #2 services a control module that affects door locks. Inspect them closely since the fuse element can crack when blowing and this is much harder to see. Pull a least #3 and plug it back in in case the contact blades have stopped comunicating with the mating connector.

To troubleshoot this effectively, you really need a cheap multimeter and the Haynes service manual for your car, #89101.
The manual has very good electrical diagrams in section 12 so you can logically trace the problem. They are available at most every auto parts chain store and cost ~ $20-25 US.

May 22, 2009 | 2005 Subaru Legacy

3 Answers

92 Subaru Legacy Power Windows Don't Work


I have a 92 that did the same. After checking fuses and the relay(located under drivers seat) I discovered that the power windows control module on drivers door was bad. Went to a salvage and bought a used for $40, pulled the door panel, unscrewed and unplugged the old one, put in the used one and everything worked fine. About a week later, the passenger side motor went out and replaced that with a used power window motor. All windows now work fine.

Jan 17, 2009 | 1992 Subaru Legacy

1 Answer

Hatch door not opening & inside window moisture


pull the rear interior cover from the door and check to see if the latch rod clips are broken or misadjusted. the moisture could be a result of a failed heater core, poor defroster operation (A/C not working, vent door, or blower motor), or the window seal could be defective.

Nov 19, 2008 | 1995 Subaru Legacy

Not finding what you are looking for?
2007 Subaru Legacy 2.5i SE Sedan Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...