Question about 1998 Isuzu Rodeo

1 Answer

The 2 bolts on the alternator are not going in . How do i line up the screws on a 1998 alternator for isuzu rodeo

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Put the alternator on first without the belt and alighn as needed to replace the bolts use the belt tentioner to replace the belt or the sliding channel on the alternatonr mounts if there is no tentioner

i hope this helps u with your problem

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size are the bolts for the alternator and tensioner pulley to mount them to a 1998 isuzu rodeo v6 3.2


Whatever they are they will be in MMs rather than inches.. most likely in the range of 1/2" or 13mm....20mm for 3/4"

Mar 27, 2016 | Isuzu Cars & Trucks

1 Answer

Cylinder head bolt tightening sequence for isuzu rodeo 1998


1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Jan 15, 2013 | 1990 Isuzu Spacecab

1 Answer

What Amp size Altenator do i need for my 1998 Isuzu Rodeo V-6 2 wd all electric?


Being an 'all electric' i would go with the 90 amp alternator, a 60 amp would work but for about 20 more dollars you can get the 90.

I hope this helps, thank you for using FixYa.

Jun 28, 2011 | 1998 Isuzu Rodeo

1 Answer

Flywheel/flexplate broke on 1998 Isuzu Rodeo, need diagram.


You will have to remove transmission. to get to the bolts.

Feb 03, 2010 | 1998 Isuzu Rodeo

2 Answers

Do you know where the alternator is located on a 97 isuzu trooper?


On the drivers side on the bottom front of the engine.

Oct 03, 2009 | 1997 Isuzu Trooper

1 Answer

Can you use another alternator in a 1998 diesel holden jackaroo


I would say yes if you managed to find an alternator with the following:
1. same bolt pattern to mount the alternator
2. same pulley size
3. same pulley resistance
4. same output current


Oct 02, 2009 | 1998 Isuzu Rodeo

1 Answer

Try to get the lower balljoint out on a 4wd isuzu rodeo , but i can't clear the outer cv joint of the 4wd shaft.


You have to start at the outer hub screw the screws around it remove the the auto hud then sirclip on the drive. The four bolts have to be removed from the balljoint. Push the shaft fully back into the axle.Pull out the bottom of the hub. Keep pushing the drive into the axle when the shaft going through the hub is over the balljoint it will lift out. Not as much work as it sounds. P.S. the brakes have to be removed also to get the hub out far enough just two screw's. Cheers

Sep 23, 2009 | 1998 Isuzu Rodeo

3 Answers

Need to replace the alternator in a 1998 isuzu rodeo


I have a 1998 Rodeo and just replaced the alternator. If I may make a suggestion, pay someone to do this. It took two of us 4 hours to replace. I am not a certified mechanic, but I know a few things about cars. I thought that I would replace it myself and save a little money! Big mistake. It is EXTREMELY hard to get too and there is NO room to work. Once you get it out, you would think that the new one would just slip back in place, not the case. I will take the car in and have it done next time. To answer your question though, yes you need to go at it from under the right side of the engine. you will need to go from the top to loosen some of the bolts. Hope this helped! Good luck!

Jan 07, 2009 | 1998 Isuzu Rodeo

2 Answers

Replace the alternator on a 97 isuzu rodeo


from Yahoo answers
The alternator is located on the passenger side of the motor at the bottom. There is a bracket attached to the motor and the alternator. You need not take the bracket off to remove the alternator. Two bolts hold the alternator to the bracket. One bolt is on the front top of the alternator and one bolt is located on the bottom front of the alternator. The bottom front bolt is attached to the tension adjustment for the alternator. Loosen the tension screw then remove the bolt going through the tension adjustment. After you loosen the top, front bolt, the alternator should be loose enough to move side to side. Remove the top, front bolt. Now you must disconnect the alternator from the power supply. Behind the alternator is a screw with a wire attached via nut. Remove this wire. Nextly there is a series of wires with a plug on the end. It is plugged into the side of the alternator. Uplug this item. You can also access both of these from the passenger side front tire well. Something to consider is that remanufactured alternators in Rodeo's as well as the Honda Passport (which has the same engine as the Rodeo) do not work and the problem(s) associated with a bad alternator,ie; not charging, no fan blower, battery light and brake light on, still exsist after replacing alternator with reman. Use a factory original alternator if possible. It will cost a little more than a reman but will most likely save you a lot of time and headache!

Hope this helps you out!!
L

Sep 29, 2008 | 1996 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...