Question about 2002 Honda Accord

1 Answer

Can't remove alternator, It's loose, but not enough room to remove

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 95 Answers

In my experiance it is easiest to remove when the driveshaft is also removed to pull alternator out the bottom.

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove an alternator for a 1999 mercury villager


remove the belt.then remove the bracket for the belt tension. then remove the bottom alternator bolt. pull alternator up to top of radiator.may need to remove upper radiator hose and cooling fan assembly to get enough room to get the alternator out.

Jun 09, 2012 | 1999 Mercury Villager

1 Answer

Why can't i get the bottom bolt off of an alternator on a 93 geo storm? I removed the top bolt and then got the bottom bolt loose. When I try to pull the bottom bolt out it stops on the tire well. I...


You may not have remove the bolt completely to get the alternator out. Try removing the alternator with the bolt out as far as it will go, or, remove the bracket that the bolt is in. Failing that, try sticking a 2 by 4 down between the engine and the fender wall and pry against something strong on the engine. It will flex a certain amount on the rubber motor mounts and may allow enough room to sneak the bolt out.

Dave

Jan 11, 2011 | Geo Storm Cars & Trucks

2 Answers

Pulling an alternator


Removing the rear-mounted alternator on early 1990s Civics and CRX can be frustrating. After removing the upper adjusting bracket bolt and the lower pivot bolt, the alternator can *almost* come out the top and almost fits behind the intake manifold.

The only easy exit path is out the left wheel well. Side access requires removing the wheel and unfastening three of the plastic retainers holding the upper end of the splash guard. But even this doesn't provide quite enough room. You need to tuck the alternator back under the intake, unbolt the lower alternator bracket (two bolts, 14mm socket) before the alternator can be removed.

The tools needed:

10mm socket -- alternator power connection, battery terminal
12mm wrench -- adjusting bracket
14mm socket -- adjusting bracket, pivot bolt, alternator bracket

Mar 30, 2010 | 1991 Honda Civic

3 Answers

Trying to remove the alternator from the car.


Removal and Installation
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Disconnect the battery. For additional information, refer to Section 414-01.
  1. Rotate the accessory drive belt tensioner counterclockwise and position the accessory drive belt aside.
  1. Remove the 8 pin-type retainers and the right lower splash shield.
    n0001884.gif
  1. Disconnect the crankshaft position sensor and release the 2 wiring harness locators from the generator splash shield.
    n0001885.gif
  1. Remove the lower generator boot pin-type retainer, fold the boot upward and disconnect the generator electrical connector.
  1. With the generator boot folded upward, position the protective cover aside and remove the generator B+ nut and terminal.
    • To install, tighten to 8 Nm (71 lb-in).
  1. NOTE: The 3 generator studs and nuts may be replaced with 3 bolts (W709986-S437) to ease the installation of the generator.
    Remove the 3 generator nuts and stud bolts.
    • To install, tighten the generator stud bolts to 8 Nm (71 lb-in).
    • To install, tighten the new generator bolts or generator nuts to 47 Nm (35 lb-ft).
  1. Remove the generator shield from the generator.
  1. Remove the generator.
  1. To install, reverse the removal procedure.

Jun 01, 2009 | 2006 Ford Five Hundred

1 Answer

1990 new yorker alternator replacement


You are right about removing the motor mount. You have to support the engine with a jack. Use a piece of plywood between the jack and the oil pan. Remove the motor mount and you should be able to lift the engine up about 2-3 inches with the jack. Remove the serpentine belt and then you should have enough room to remove the alternator.

Apr 19, 2009 | 1990 Chrysler New Yorker

2 Answers

I have 97 mitsibishi 3000GT alternator not workin got all the bolts off but how does it come out top or bottom?


the only way to really remove it is to take it out from the bottom, but get ready for a project. The only way to take it out of the bottom is to take the drive axle out, luckily you do not have to take it out of the transmission though. Good luck

Apr 17, 2009 | 1997 Mitsubishi 3000GT

1 Answer

1998 Grand Voyager needs alternator replaced


First I removed both bolts to the alternator and and then a horizontal bracket. Because the alternator is on the backside of the engine I removed all the bolts (except one I could not reach) to the vertical bracket that holds the top bolt of the alternator that I could reach which allowed me to move the vertical bracket enough to wiggle the unit between the side of the engine and hoses and wires that run in the area. It is tight but there is just enough room to remove and reinstall the alternator.

Dec 19, 2008 | 1998 Dodge Grand Caravan

2 Answers

Remove alternator from car 2002 ford focus


remove cooling fan assembly and drop alternator from bottom or top.

Aug 24, 2008 | 2002 Ford SVT Focus

Not finding what you are looking for?
2002 Honda Accord Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...