Question about 1998 Audi A4

1 Answer

Ive just had new brake discs and pads al laround now i have clicking noise on the front wheels which i can feel through the pedal

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

One of the rotors is warped or out of round, the click you hear is the caliper moving back and forth, and it pulsates back to the pedal, get it replaced

Posted on Nov 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake peddle is low,


Pedal, not peddle. First make sure reservoir is full at the brake master cylinder. Then check your brake pads (for disc brakes) and/or brake shoes (for drum brakes). When the pads or shoes are very worn down, you will get a low pedal. If you have disc brakes on the front and drums on the rear wheels, first try just replacing the front brake pads. If you get a good pedal after the front is done, many people tend to let the rear brake shoes go unless they are making noise. These systems are designed to put most of the braking force on the front discs, so the rear shoes do not need changing as often.

May 11, 2017 | Cars & Trucks

2 Answers

How do I stop the front disc brakes from clicking on my 95GMC g3500 Vandura.


YOU NEED TO REPLACE THE HARDWARE . THE LITTLE CLIPS THAT MOUNT ON THE CALIPER ARE LOOSE ALLOWING THE PADS TO CLICK

Dec 19, 2014 | Cars & Trucks

2 Answers

When i press my brakes it judders and makes a loud noise


Ok, if it shakes in the seat when braking then it is the rear brakes, if it shakes the steering wheel it is the front brakes. New pads and Discs, but were the discs turned on a lathe? They shouldn't need to be turned if they were brand new, but....

Nov 11, 2011 | Cars & Trucks

1 Answer

Metal on metal noise when driving. Sounds like brake noise when brake pads are in need of replacement. Sound goes away when the brake is applied. Car only has 20,000 miles on it (2006).


Hello tgiro7: My name is Roger and I will help with your question. The fact the noise goes away when stepping on the brake pedal says the problem most likely is in the brake area. The pads could be worn out even at 20,000 miles.If the noise sounds like it comes from the front remove the wheels and check the front pads. If the pads are bad most likely the rotors are also bad.Same would apply if the noise emits from the rear. When you have the wheels off check to make sure the calipers will slide in and out on the mount pins. Should they be stuck on binding the pads will wear excessively and prematurely fail. The calipers must move freely on the pins. If you drive with your left foot on the brake pedal? The amount of pressure required to apply the brakes and not stop the vehicle is 1 to 2 pounds of pressure. Wont turn on the brake lights but will put pressure on the calipers. This in turn will wear out the brake pads. Another thing to look at would be an out of adjustment brake switch. Reach down and grab hold of the brake pedal. Give a firm tug on the pedal. Should you feel the pedal give and hear a click or two the switch was set to deep and holding the brakes on.
Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Jun 16, 2011 | Chrysler Crossfire Cars & Trucks

2 Answers

My 1998 ford escort brake peddle started pulsing and then a noise. Checked fluid, not down any fluid, and no leeks, just feels like I can not stop well., No ABS lite til yesterday, then it came on after...


Normally a "pulsing" brake pedal means that that you have a warped brake rotor or the brake caliper is lose. I would start by taking the front wheel off and inspecting the brake pads and the rotor. If the brake pads are worn down bad replace them. Pay special attention to the brake rotors also as if the are grooved very bad, they should also be replaced.

Nov 15, 2010 | 1998 Ford Escort

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

3 Answers

2007 camry brakes vibrating


Installing new brake pads on toyota camry solara 2006 front rotors and pads and rear pads. Steering wheel would shake while breaking on 50+ miles per hour speeds. All fixed now.

Jun 22, 2010 | 2007 Toyota Camry

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    2 Answers

    Brakes are pulsing


    new rotors, machine rotors or just a pad slap?
    pulsing indicates warpage, is if felt in the steering wheel or the brake pedal? did you do front and rears?
    is it drum or all wheel disc brakes?

    Apr 13, 2010 | 1999 GMC Jimmy

    Not finding what you are looking for?
    1998 Audi A4 Logo

    Related Topics:

    105 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Audi Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14363 Answers

    Are you an Audi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...