Question about 2005 Mercury Mariner
Lift gate up remove the 2 screws on the side of the light housing. The back of the light housing is held in by pin style snap fastner. Two ways 1 grab top and bottom pull hard and fast and hope to pop out both. 2 get a hold of the top and just pop it out turn it out grab and pull (always pull straight or the pins will break)
Posted on Jan 03, 2011
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The Tail Lights Are Accessed From The Inside Of The Trunk There Will Either Be A Panel Immediately Behind Where The Light Is Or Carpet. Remove It And It Will Give You Access To The Rear Of The Bolts Just Grab Twist And Pull And The Light Will Come Out.
Posted on Jan 26, 2009
No tools needed.
Beetles: Round plug inside trunk pops out.
Beetle Convts: Grille-looking rectangular panel pops out.
Reach in and you'll feel a large finger-grip able nut, back it off (DON'T DROP
IT) and place it somewhere retrievable. Take a small-flat-bladed screwdriver and wrap it in cloth so you don't scratch the paint. Poke said protected blade between the inside body joint and the tail light, gently pry tail light out. Remove offending bulb, replace with new. Installation is, as they say, the reverse of removal.
Posted on Jul 16, 2009
Unscrew the knob behined the light in the Boot / Trunk and the use a small screwdriver on the OUTSIDE of the light on the right handside as you look at the light in the middle on the outside. You will feel a little spring clip and as you push gently the light will pullout forward.
Go to the above link and you will get picture wise explanation for the same tail light bulb replacement. It has step by step picture explanation.
Posted on Oct 05, 2009
Tips for a great answer:
Oct 16, 2015 | Dodge Cars & Trucks
Jul 01, 2015 | Hyundai Cars & Trucks
May 22, 2011 | 1992 Buick Park Avenue
Apr 30, 2011 | Volkswagen Golf Cars & Trucks
Mar 04, 2011 | 2000 Buick LeSabre
Feb 26, 2011 | 2007 Suzuki XL-7
Jan 27, 2011 | 1999 Volvo C70
process for replacing tail light bulbs is the same in all models. If
you have a burnt-out tail light bulb, you may need to replace the
brake light, the reverse light or the turn signal. The procedure to
replace each of the bulbs is the same.
1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.
Remove the two screws from the tail light assembly. Pull the tail
light out and inspect the back for two bulbs. The top bulb is the
brake light and turn signal. The bottom bulb is the reverse bulb.
Determine which bulb you need to replace.
the tail light into its cradle. Hold it with one hand and replace
the Phillips head screws with the other.
Dec 03, 2010 | 2008 Hummer H3
Open the endgate or liftgate.
Remove the screws that retain the tail lamp assembly to the vehicle.
Tail lamp assembly removal
Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.
Remove the bulbs from the sockets.
Install the bulbs into the sockets.
Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.
Install the tail lamp assembly to the vehicle.
Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).
Oct 23, 2010 | 2000 Oldsmobile Bravada
446 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: