Question about 1993 Mercury Villager

1 Answer

Where is the speed sensor located on a 1993 mercury villager and how do you fix it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

It's on the top reear of trans. often hard to pry out. 10 mm bolt, two pin connecotr. what is issue?

go here

http://groups.yahoo.com/group/villagerquest/

Posted on Dec 03, 2010

  • gerry bissi Dec 03, 2010


    here's what it looks like. Do not pry on plastic part, only on base. First, just clean the termainls & connector and see if that fixes it. Gear could be worn too. $5 at dealer

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 mercury villager van, passenger auto seat belt motor running continuously & seat belt won't work. Drained battery. Where is the fuse located?


Engine compartment main fuse panel 30 AMP fuse Fuse #4 scroll down and look at this diagram picture on this link. http://www.autogenius.info/mercury-villager-1st-generation-1993-1998-fuse-box-diagram/ caution, this fuse runs power seats, windows and sun roof as well.

Mercury Villager 1st Generation 1993 1998 fuse box diagram Auto Genius

Oct 15, 2016 | 1994 Mercury Villager

1 Answer

Location removal and installition of transmission speed sensor


Hi Anonymous, the link below is a youtube video showing how to replace a speed sensor on a 2000 mercury villager, I hope this motor and your motor are similar, Good luck and CHEERS..
How to replace speed sensor on 2000 Mercury Villager Nissan Quest

Apr 17, 2016 | 2002 Mercury Mountaineer

2 Answers

Where is the TPS on a 2000 Mercury Villager?


tps is throttle position sensor is located at the intake of the of the engine opposite side where the throttle cables end

Feb 14, 2011 | 2000 Mercury Villager

1 Answer

1993 mercury villager when diriving at speeds over 50 car will lose power and you have to play with gas peddle to get speed back up, than car will be ok for short time and do it again


Clean the MAF sensor with carb cleaner first. It's in the air intake tube, spray the tiny wires inside with carb cleaner to get varnish off heated wire. Do not touch or move them.


Gerry

http://groups.yahoo.com/group/villagerquest/

Dec 31, 2010 | 1993 Mercury Villager

1 Answer

How to replace the speed sensor on a 2000 mercury villager


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disconnect the VSS electrical connector.
  4. Remove the VSS hold-down bracket bolt and remove the bracket.
  5. Remove the VSS from the vehicle.
  6. The installation is the reverse of removal. When installing the VSS hold-down bracket, tighten the bolt to 44–61 inch lbs. (5–7 Nm).


8ef1d6d.gif
Vehicle speed sensor location

Sep 13, 2010 | 2000 Mercury Villager

1 Answer

Fix speedometer on 93 mercury villager


remove the 2 pin connector from the vehicle speed sensor on the top rear of th trans. clean terminals, see if fixed. If still bad, nylon gear on speed sensor is bad. 10 mm bolt holds it in but most are corroded in place and impossible to remove. Only twist & pry on metal base.

http://groups.yahoo.com/group/villagerquest/

Apr 25, 2010 | 1995 Mercury Villager

2 Answers

93 mercury villager check engin light comes on for 2 days then off for a day then back on i dont know where to plug in my scanner


I too have a 93 Villager. Recently the check engine light came on especially on the highway cruising speed and it turned out to be caused by clugged EGR. My mechanic cleaned up the carbon build-up ( not replace EGR) from all those 170K miles and it seems to fix the problem. He charged me $150 for the labor only. Also the gas mileage seems to improved a bit as well.

Oct 27, 2009 | 1993 Mercury Villager

1 Answer

How do you remove a stuck speed sensor?


very difficult. They corrode in place due to steel contacting aluminum.

Soak base with penetrating oil. Tap steel base on side with chisel to break it loose. Try to get vice grip on base and tap back and forth to twist it back and forth to free up. It takes a lot of effort and time.

go here too.


http://groups.yahoo.com/group/villagerquest/

Apr 23, 2009 | 1993 Mercury Villager

Not finding what you are looking for?
1993 Mercury Villager Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5530 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...