Question about 2002 GMC Safari

1 Answer

Where is the camshaft position sensor(CPS) located at on a 2002 GMC Safari Van

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

2002 Safari 4.3L engine, cam sensor, same as pick-up coil, sits in ignition distributor, will be the one with three wire connector, held on with two small bolt's in the distributor.

Posted on Nov 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crank sensor


If you go to Google and type in "2002 GMC Yukon XL Crankshaft Position Sensor"...click enter...then look for the tab that says "images". The first image I found shows the location of the CPS. If you're not able to view the image, the sensor is located on the lower right rear of the engine block.

Good luck!
Jason

May 21, 2014 | 2002 GMC Yukon XL

1 Answer

Where is the cmp located on a 99 amigo 3.2 engine


the camshaft position sensor (CPS) is located on the side of the left cylinder head. It's shadowed underneath the intake manifold.

Feb 21, 2012 | 1999 Isuzu Amigo

1 Answer

Location for camshaft/crankshaft sensor 9-volt supply circuit for a 1992 dodge dynasty 3.3L


The camshaft Position Sensor (CPS) is located on the timing gear cover.

michael_cass_450.jpg
The Crankshaft Position Sensor is located on the transmission bellhousing.

michael_cass_451.jpgHope this was some help to you?

Jul 25, 2011 | 1992 Dodge Dynasty

2 Answers

Does my 1994 gmc safari 4.3 z have a cam shaft sensor ? if so does anyone know where it is located ? \i have looked everywhere and can't seem to locate it?


The camshaft sensor is located in the distributor. The sensor functions as an ignition device in the Enhanced Distributor Ignition system. In the event of failure or damage, the sensor is not directly involved with driveability.

Jan 08, 2011 | 1994 GMC Safari

1 Answer

I have a problem with my 96 caravan P0340 Code can you help me? Van will run and sometimes shut down and won't start for several hours.


P0340 Camshaft Position Sensor Circuit Malfunction

This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it. Take it somewhere to get it checked out to see which of the above it is.

Jan 04, 2011 | 1996 Dodge Caravan

1 Answer

How do I change a camshaft position sensor on a 2002 Trailblazer?


Hi : Your CPS (Camshaft position sensor) is located on the Engines Front Cover (Timing Chain Cover) its right below your Cylinder Head ,Get a Good Bright Light to Locate it ,You'll see a Wiring Connector plugged into the Sensor, emove the electrical Plug.
Then you have 1- Screw Holding it in Place -Remove the Retaining Screw and Remove the Sensor.

To replace it with your new Camshaft Sensor Put the Camshaft Sensor in where you took out your Old one,Replace the Retaining Screw Tighten up Good And Snug,Put the Wiring connector back on the Sensor and Your Done. This will get your job done,Let me know Please how My Solution/instructions have Helped you. Thanks From d_hubbs

Jun 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

2000 safari van no spark to spark plugs turns over but won't fire


Sounds like it is either a bad coil pack, cam position sensor or crank position sensor. The coil pack delivers the spark to the plugs and the 2 sensors tell the computer when to tell the coil pack to spark.

Jun 05, 2010 | 2001 GMC Safari

1 Answer

Were is the cam sensor on a 1996 chevy 5.7 liter engine?


if you are referring to the CPS camshaft position sensor, it doesn't appear that your engine has one. my auto parts store catalog says that it has no info for that part. I have a 95 chevy van with a 5.7 and it doesn't have a cps..........

Mar 10, 2010 | 1996 Chevrolet K1500

3 Answers

2005 gmc safari wont start checked coil spark


how much fuel pressure you have when turn key on

Feb 04, 2010 | 2005 GMC Safari

1 Answer

Where is the camshaft sensor located?


Camshaft sensor is in the distributor.Distributor will have to be remove from engine to replace camshaft sensor.

Nov 17, 2009 | 1996 GMC Safari

Not finding what you are looking for?
2002 GMC Safari Logo

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...