Question about Mazda MAZDA6

Open Question

I need 2003 mazda 6 2.3 serpentine belt routing

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: I need the routing diagram for the serpentine belt

there should have been a picture under your hood , but here ya go .

dc8b3a4.jpg

Posted on Jan 08, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: serpentine belt diagram

The serpentine belt routing should be labeled on your radiator shroud. Look around the engine compartment like the hood or radiator fram suport and there should be a label with the the belt routing.
Good luck and hope this helps

Posted on Apr 19, 2009

old marine
  • 1983 Answers

SOURCE: need routing diagram for 2000 lincoln town car serpentine belt

There's a diagram at this link.

Posted on May 11, 2009

greg_margo
  • 1959 Answers

SOURCE: i NEED 2005 mazda6 Serpentine Belt Routing

There are 2 engines for your Mazda 6, a 2.3 and a 3.0. Below are both diagrams:
2.3
e557cdf.jpg

3.0
c9ae9a7.jpg

Posted on Sep 08, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram for a 2011 dodge 2500 cummings serpentine belt.


Jeff, Check the attached links,instruction and guides, diagram for a serpentine belt, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Amps Belt routing Installation and system start up for 6 7L Cummins
Serpentine Belt Routing
Drive belt routing
2011 dodge 6 7 cummins serpentine belt diagram Google Search

May 22, 2016 | 2011 Dodge Ram 2500

1 Answer

I need a diagram for the serpentine belt on a 2003 Rav4


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 02, 2012 | 2003 Toyota RAV4

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    PLZ I NEED FOR A 04 MAZDA MAZDA 6 V6 THE SERPENTINE BELT DIAGRAM THANK YOU SOO MUCH FOR UR HELP !!!


    Hello ezzywaylogis,

    Below is a diagram of the belt routing.

    netvan_209.png

    I hope this helps.

    Regards,

    Jerry

    Aug 28, 2011 | 2004 Mazda 6

    1 Answer

    I need the serpantine belt routing diagrams for a 1993 Mazda 626 v-6


    Question Posted by Asker under the 1994 Mazda for a 1993 Mazda.

    Click on the following: free, direct Link. It has several Diagrams including the Serpentine Belt Diagram for your 1993 Mazda 626 2.5L DOHC V6. It has the 2.0L DOHC 4-Cyl Diagrams as well as Instructional and Directional Diagrams that will help you.

    http://www.2carpros.com/car_repair_information/year/1993/make/mazda/model/626/1993_mazda_626_drive_belt_routing_diagram.htm

    Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

    Apr 03, 2010 | 1994 Mazda 626

    2 Answers

    Need diagram of drive belt assembly forcaddy


    You didn't list your motor size so please pick the applicable diagram:

    ba0b112.gif
    Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines

    9dcebd3.gif
    Accessory serpentine belt routing—5.7L engines with A/C

    bb89ba7.gif
    Accessory serpentine belt routing—5.7L engines without A/C

    27f4999.gif
    Accessory serpentine belt routing—6.5L Diesel engines

    4d67005.gif
    Accessory serpentine belt routing—7.4L engines

    491a0a4.gif
    Accessory serpentine belt routing—8.1L engines

    Oct 26, 2009 | 2002 Cadillac Escalade Ext

    3 Answers

    NEED DIAGRAM FOR ROUTING THE SERPENTINE BELT


    PLEASE DON'T FORGET TO RATE--You didn't post the size of motor so please pick the applicable one:

    e8f5627.gif
    Accessory serpentine belt routing—4.8L, 5.3L and 6.0L engines

    793398d.gif
    Accessory serpentine belt routing—4.3L, 5.0L and 5.7L engines without A/C

    b701ba4.gif
    Accessory serpentine belt routing—4.3L, 5.0L and 5.7L engines with A/C

    a8d5a93.gif
    Accessory serpentine belt routing—6.5L Diesel engines

    7f5d3cb.gif
    Accessory serpentine belt routing—7.4L engine

    10dba31.gif
    Accessory serpentine belt routing—8.1L engine

    Oct 22, 2009 | 2004 Chevrolet Express

    2 Answers

    I NEED 2005 mazda6 Serpentine Belt Routing


    There are 2 engines for your Mazda 6, a 2.3 and a 3.0. Below are both diagrams:
    2.3
    e557cdf.jpg

    3.0
    c9ae9a7.jpg

    Sep 08, 2009 | 2004 Mazda 6

    1 Answer

    I NEED mazda 6 2005 Serpentine Belt Routing Diagram. anyone/


    if you go to autozone.com and register, you will be able to view the diagram. Its free and fast.

    Sep 08, 2009 | 2004 Mazda 6

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    126 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8266 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...