Question about Saab 9 5

1 Answer

I AM DOING THE HEAD GASKET ON 1999 SAAB 95 4 CYL I NEED THE TORQUE SPEC ON CYL. HEAD

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Torque spec

Step 1- 44 Ft.Lbs.
Step 2- 59 Ft.Lbs.
Step 3- Tighten bolts an additional 90 degrees.

Here the head bolt's tightening sequence.

I AM DOING THE HEAD GASKET ON 1999 SAAB 95 4 CYL I - bcas1298_1.gif

Posted on Nov 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Need torque spec's for 1999 Grand Am 2.4L motor valve pan gaskets bolts? thanks


I need know the torque head Pontiac Grand am se 1999. Machine 2.4

Mar 24, 2012 | 1999 Pontiac Grand Am GT

1 Answer

Can you give me the torque specifications for valve cover gasket for a saab 1999 95 four cylinder?


The specs that i have is 11 foot pounds, start by hand tightening the bolts and then torgue them in a clock wise fashion starting from the center
ex. 8 4 1 5 9
7 3 2 6 10

May 23, 2011 | Saab 9 5 Cars & Trucks

1 Answer

Saab 95 Aero 2.3 turbo. I need torque settings for big end bearings and cylinder head bolts.


CYLINDER HEAD BOATS TORQUE FIRST PASS 29.5 FT LBS SECOND PASS 44 FT LBS.THEN TIGHTEN ADDITIONAL 90 DEGREES FOR MAIN BEARINGS 15 FT LBS TIGHTEN EACH BOAT ADDITIONAL 70 DEGREES ROD BEARINGS 15 FT LB TIGHTEN ADDITIONAL 70 DEGREES. CRANKSHAFT DAMPER BOLTS 130 FT LBS.

Jan 26, 2011 | 1999 Saab 9-5

2 Answers

What are the cylinder head torque specs for a 1999 cadillac deville 4.6l


I can help you with this but I have to ask one question. Have you already taken this apart and putting it back together? Did you rethread all the head bolt holes because they strip out when you tighten them and you will ruin the head gaskets. Let me know, I have don't this job quite a few times. I'll have to look up the actual torque specs. Also you are wanting the spec for the cylinder head bolts and not the cylinder head cover bolts right?

Jun 12, 2010 | 1999 Cadillac DeVille

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

2 Answers

Blown Headgasket


without mechanical knowledge, best left to a garage. if you have a bit of knowhow then do an assessment of what is connected to the head, inclusive of exhaust manifold and fuel inlet manifold, wiring etc.Once you decide how to do it, note where all bolts and wires go.Clean every bit of old gasket off all faces and as the head is alloy get a head skim from a motor factor or machine company. You will need a new set of cylider head bolts and full head gasket set. Torque settings , however will need to be obtained along with the head bolt sequence for retightening

Aug 07, 2009 | Saab 9 5 Cars & Trucks

2 Answers

Head gasket torque specs


Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Apr 30, 2009 | Ford F-150 Cars & Trucks

1 Answer

1999 Saab 9-5 oil pan torque spec


they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Mar 06, 2009 | 1999 Saab 9-5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...