Question about 1990 Buick Century

1 Answer

Need mounting clips for left rear door trim - 1990 Buick Century

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Buick Master
  • 5,332 Answers

Take one that isn't broken and bring it in to your local auto parts store. They should have or get those for you. You can also check with a buick dealer. They usually have them in stock.

Posted on Nov 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you install a driver seat plastic shield on a 2004 Ford Explorer? Its the piece of hard plastic between the door and the seat - part number 1L2Z-7862187-BAC


see if this helps
  1. Remove the rear trim screw.

snorkelbobby_44.gif
  1. Remove the lower trim screw.

snorkelbobby_45.gif
  1. Release the side trim front retaining clip.
  2. Pull the lumbar mechanism out slightly from the seat.
  3. Push down and pull out, releasing the side trim front retaining clip.
  4. CAUTION: Take care when removing the side trim cover. Excessive force will break the mounting tabs.

snorkelbobby_46.gif
Release the side trim from the mounting bracket.

snorkelbobby_47.gif
  1. Disconnect the seat control switch electrical connector.

Mar 25, 2011 | 1998 Ford Explorer

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

How to replace rear blower motor motor in 2006 chrysler town and country van


from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Nov 04, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

How to replace the blower motor in a dodge 2001 caravan


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1549e60.jpg

      Fig. Removing the trim panel to access the rear blower motor

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    823bf07.jpg

    Fig. The rear blower motor is held in place by four screws


To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Nov 01, 2010 | 2000 Dodge Caravan

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

Need to remove left rear door panel


  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

May 22, 2009 | 2006 Chevrolet Silverado

1 Answer

Window regulator replacement


Window Regulator, Rear Door, Explorer Removal
  1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .
Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation
  1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.
  1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.
  1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .
  1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .
  1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.
  1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
    33c9359.gif
  1. If equipped with power windows, disconnect the wire from the regulator.
  1. Remove the rear door window glass as described in this section.
  1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.
  1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
  1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.
  1. Remove two upper regulator attaching nuts.
  1. Remove regulator from the front door (20125) .
Installation
  1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.
  1. Install regulator into access hole in inner panel.
  1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).
  1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).
  1. Install two upper regulator attachment nuts.
  1. Install door glass as outlined under Door Glass Installation.
  1. Adjust glass as outlined under Adjustments .
  1. Reconnect wire to regulator, if equipped.
  1. Check operation of window regulator.
  1. Install door watershield and trim panel. Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

2000 Honda Odyssey rear wiper motor replacement


You are probably correct in thinking its the wiper motor. You can do this but you will need to remove all the interior trim from the rear hatch first. Get a trim clip removal tool at a parts store...it will work much better than just a flat blade screwdriver. You'll have to remove the trim panels starting in order from the top of the door, then the left rear window side trim, then right rear window side trim, then the grab handle, and finally the main rear hatch trim panel. Once inside, removing and replacing the rear wiper motor is easy. You'll start by lifting the cover on the wiper arm retention nut. Remove this nut to get the wiper arm off, then remove the nut under neath which is the motor shaft mounting nut. Now, back inside to remove the other 3 motor mounting bolts. Don't forget to disconnect the connector for the motor wires. Reverse steps to replace.

Mar 29, 2009 | 2000 Honda Odyssey

1 Answer

Removing rear door panel


Remove the door window regulator handle and then remove clip using a piece of cloth (Manual type only)
Remove the rear door inside handle housing.
Remove the mounting screws (3EA) from the trim fasteners and the door trim panel to pry off. Disconnect the connector.
Insert a trim panel remover between the trim fasteners and the door trim panel to pry off. Disconnect the connector.
Remove the door pull handle mounting bracket and door inside handle.

May 29, 2008 | 2001 Hyundai Sonata

Not finding what you are looking for?
1990 Buick Century Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...