Question about 2006 Chrysler Sebring

1 Answer

When i turn headlight on my 2006 chrysler sebring the windshiled wipers start working,then stop and then go on again. what should I do?

Posted by on

  • nadia413 Nov 11, 2010

    How much will it cost to fix this problem? Do I have to take wheel off to replace it?

  • nadia413 Nov 11, 2010

    How do I disable the airbag? Can I do it myself?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 17,970 Answers

I'm assuming that you have "multi-switch" for this (headlights and winshield wipers), its possible that this multi switch go to bad and need replace it. First check wires aren't loss orn any ground there.

Tell us news.

Posted on Nov 11, 2010

  • ZJ Limited
    ZJ Limited Nov 11, 2010


    Multi-Function (Combination) Switch - REMOVAL & INSTALLATAION

    Should any function of the switch fail, the entire switch assembly must be replaced.



    Fig. Components of the multi-function switch (click for zoom)

    1. Set the steering wheel and the front wheels to the straight ahead position.
    CAUTION
    The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the steering column. Failure to do so may cause accidental deployment of the air bags, resulting in unnecessary SIR system repairs and/or personal injury.

    2. Disable the SIR system. Refer to Air Bag (Supplemental Restraint System), disarming the system.
    3. Remove the steering column lower cover retaining screws.
    4. Loosen the lower section of the instrument cluster hood for clearance, as necessary.
    5. Remove the steering column upper cover.



    Fig. Remove the multi-function switch mounting screws

    6. Remove the multi-function switch mounting screws.
    7. Disconnect the wiring connectors from the multi-function switch.
    8. Lift the multi-function switch upward to remove.
    NOTE
    The turn signal flasher and hazard warning flasher are combined into one unit called a combination flasher (combo-flasher). An inoperative or incomplete turn signal circuit will result in an increase in flasher speed. The flasher, which is serviced separately from the switch, is mounted to the back of the multi-function (combination) switch. The flasher is black in color for ease of identification.

    To install:

    1. Install the multi-function switch.
    2. Attach the wiring connectors.
    3. Install the multi-function switch mounting screws and tighten to 20 inch lbs. (2 Nm).
    4. Install the steering column covers as follows:
    1. Install the upper cover onto the steering column.
    2. Tighten the lower part of the instrument cluster hood.
    3. Install the lower steering column cover retaining screws and tighten to 17 inch lbs. (2 Nm).

    5. Enable the SIR system. Refer to Air Bag (Supplemental Restraint System), arming the system.
    6. Test the switch functions.


    Try to look in THIS LINK for right part replacement amd search in ELECTRICAL (Chassis>> Sitches) section as MULTI FUNCTION SWITCH.

    Hope this helps.

  • ZJ Limited
    ZJ Limited Nov 12, 2010

    Disarming the System




    1. Disconnect and isolate the negative battery cable.


    2. Wait 2 minutes to allow the system capacitor to fully discharge before servicing the vehicle.

    Disconnect and isolate the battery negative cable before beginning
    any airbag system component diagnosis, testing, removal, or installation
    procedures. Allow system capacitor to discharge for two minutes before
    beginning any component service. This will disable the airbag system.
    Failure to disable the airbag system may result in accidental airbag
    deployment, personal injury, or death.

    Do not place an intact
    undeployed airbag face down on a solid surface. The airbag will propel
    into the air if accidentally deployed and may result in personal injury
    or death.

    When carrying or handling an undeployed airbag, the trim
    side (face) of the airbag should be pointing towards the body to
    minimize possibility of injury if accidental deployment occurs. Failure
    to do this may result in personal injury or death.

    Replace airbag
    system components with OEM replacement parts. Substitute parts may
    appear interchangeable, but internal differences may result in inferior
    occupant protection. Failure to do so may result in occupant personal
    injury or death.

    Wear safety glasses, rubber gloves, and long
    sleeved clothing when cleaning powder residue from vehicle after an
    airbag deployment. Powder residue emitted from a deployed airbag can
    cause skin irritation. Flush affected area with cool water if irritation
    is experienced. If nasal or throat irritation is experienced, exit the
    vehicle for fresh air until the irritation ceases. If irritation
    continues, see a physician.

    Do not use a replacement airbag that
    is not in the original packaging. This may result in improper
    deployment, personal injury, or death.

    The factory installed
    fasteners, screws and bolts used to fasten airbag components have a
    special coating and are specifically designed for the airbag system. Do
    not use substitute fasteners. Use only original equipment fasteners
    listed in the parts catalog when fastener replacement is required.

    Good luck.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Windshield wipers stop working when the defroster is on


The only thing they have in common is the ignition switch.

Dec 18, 2015 | 2007 Chrysler Sebring Sedan

1 Answer

What fuse is 14 and 15.??


hi there I wanted to tell you my chrysler is 2006 ,but having said that #14 is 10 amp red for the radio
and 15 is 10 amp red for turn signal,wiper switch,seat belt control module ,wiper relays,rear window defroster relay like said that's for 06 six cylinder hope that helped. Esther

May 27, 2014 | 2002 Chrysler Sebring

1 Answer

2002 Sebring conv. the turn signals, radio, and


the fuse box under the dash is also a body control module a computer have it checked

Aug 27, 2013 | 2004 Chrysler Sebring

1 Answer

WINDSHILE WIPERS


could be a bad switch or motor

Nov 25, 2011 | 1997 Pontiac Grand Prix

1 Answer

Model: 2003 C240 problem: wiper blades "park"


model: 2001 C240 problem: wiper blades "park" almost in the middle of a windshiled when turned off. When wiper blades are on they cover complete range of a windshiled.

Feb 01, 2011 | 2003 Mercedes-Benz C-Class

1 Answer

Windshiled wipers will work on the intermittet stage for about 10-15 minutes then automatically goes to regular speed and will not shut off. When stop vehicle and shut engine off and let sit 15-20 minutes...


windshiled wipers will work on the intermittet stage for about 10-15 minutes then automatically goes to regular speed and will not shut off. When stop vehicle and shut engine off and let sit 15-20 minutes wipers will shut off. When needed again same thing will happen This is on a 2003 Chevrolwt express Va

Feb 09, 2010 | 2003 Chevrolet Express

1 Answer

PT CRUISER 2003 WINDSHILED WIPERS STOP WORKING SUDDENLY . ONLY THE FRONT


Check the fuse and then check the wire harness to the wiper motor. The information to which fuse should be in your owners manual. If you are having problems loacting the fuse panels for the wiper, keep me posted. Be glad to answer any more questions you may have. Good luck.

Oct 17, 2009 | 2003 Chrysler PT Cruiser

1 Answer

My headlights,windshield wipers, and turn signals wont work


check all your fuses. replace any and all bad ones. if fuse blows again u have a short somewher

Jul 02, 2009 | 2006 Chrysler PT Cruiser

2 Answers

Replacing headlight bulbs on a 2006 chrysler sebring


Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Feb 06, 2009 | 2006 Chrysler Sebring

Not finding what you are looking for?
2006 Chrysler Sebring Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...