Question about 2005 Chrysler 300

2 Answers

I have a 2006 chrysler 300 3.5 where is the thermostat located at?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 205 Answers

Right in the front of the engine,on the top you are going to see the radiator hose connected to the part where the thermostat is inside.

Posted on Nov 11, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where is a thremostat in 3.5 L chry 300

Posted on Jan 27, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove and replace the water pump on a 2006 Chrysler 300 hemi 5.7 l.


5.7L Engines

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Drain the cooling system.
  4. Disconnect negative battery cable.
  5. Remove the upper radiator hose.
  6. Disconnect cooling fan electrical connector.
  7. Remove cooling fan mounting bolts.
  8. Remove the radiator cooling fan assembly from vehicle.
  9. Remove the radiator fan assembly.
  10. Remove accessory drive belt.
  11. Remove thermostat.
    NOTE The water pump mounting bolts are different lengths. Note the location of the water pump mounting bolts.
0996b43f80200d65-mw3da2o1okphbx00ygfzxzdl-4-0.jpg To install:
  1. Install water pump and mounting bolts. Tighten mounting bolts to 20 ft. lbs. (28 Nm).
  2. Make sure double ended bolt is in the proper location. Tighten double ended bolt to 20 ft. lbs. (28 Nm).
  3. Position the radiator cooling fan assembly in vehicle.
  4. Install cooling fan mounting bolts. Tighten to 50 inch lbs. (6 Nm)
  5. Connect the cooling fan electrical connector.
  6. Install the upper radiator hose.
  7. Install thermostat.
  8. Install the accessory drive belt.
  9. Install the radiator fan assembly.
  10. Connect negative battery cable.
  11. Fill the cooling system.
  12. Pressure test cooling system.

Mar 16, 2017 | 2006 Chrysler 300

1 Answer

Where is the crank shaft sensor located on a 2006 chrysler 300 2.7lit.


the crankshaft sensor location: upper right side of transmission bellhousing, held by one bolt,accessed from under car use jackstands for safety

Aug 26, 2014 | 2006 Chrysler 300

1 Answer

Wheres the ac drain on a 2006 chrysler 300


The battery on a 2006 Chrysler 300 is located in the trunk like many cars now a days.---------------------------------------------------------------------
galletto 1260

Dec 13, 2012 | 2006 Chrysler 300

1 Answer

Starting problems with 2006 Chrysler 300 3.5 v6


Hello 2006 Chrysler,

If your talking about the component that is located along the air duct run from the air filter to the throttle body it is caled a MAF sensor.
Mass Air Flow Sensors Components

Jul 23, 2017 | 2006 Chrysler 300

1 Answer

Hi I need help with locating a relay on a chrysler 300, 2006.


there are 86 relays in that car wich one you need ?

Nov 21, 2010 | 2006 Chrysler 300

1 Answer

My coolant light come on and my tempeture gage shot to the red zone in my 2006 chrysler 300 can I reslove this matter or do I have to take it to the dealership


Simply replace your heat sensor located next to your thermostat housing on the top of your motor. Also its a good idea to check your coolant level sensor located within the plastic overflow bucket. Both can cause this un-reliable reading on the heat gauge. Be sure that the thermostat is not sticking shut or open as it to can cause this problem as well as the cooling fan not comming on when it should located by your radiator.

Oct 21, 2010 | 2006 Chrysler 300

1 Answer

How do you install a thermostat houser for a chrysler 300


You mean a thermostat housing? Thats not a commonly installed item as the old one is usually good enough to use over again when the thermostat is changed.
It is usually at the end of the upper radiator hose on the engine side. Try there. Make sure you have a new gasket from the parts house. clean the old gasket off very carefully. A tiny bit of rtv, very thin will help insure that it doesnt leak.
Drain the radiator first if you dont want a big mess. ;)

Mar 06, 2010 | 2006 Chrysler 300

Not finding what you are looking for?
2005 Chrysler 300 Logo

800 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...