Question about 2000 Chevrolet Monte Carlo

1 Answer

How to change battery - 2000 Chevrolet Monte Carlo

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 36 Answers

  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
    how to change battery - 513051.gif
    tif.gif
  3. Disconnect the battery positive cable terminal bolt from the battery.
    513047.gif
    tif.gif
  4. Remove the battery hold down retainer bolt (1).
  5. Remove the battery hold down retainer (2). Important: Do not tip the battery more than 40 degrees during removal.

  6. tif.gif
  7. Remove the bahow to change battery - 201375.giflator from the battery.
Installation Procedure

    201375.gif
    tif.gif
  1. Install the battery insuhow to change battery - tif.gifo the battery.
    513047.gif
    tif.gif
    Important: Do not tip the battery more than 40 degrees during removal.
  2. Install the battery (3) to the battery tray.
  3. Install the battery hold down retainer (2). Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to partshow to change battery - 513051.gifms.
  4. Install the battery hold down retainer bolt (1). TightenTighten the battery hold down bolt to 18 N·m (13 lb ft).

    513051.gif
    tif.gif
  5. Connect the battery positive cable to the battery. Tighten
    Tighten the battery positive terminal bolt to 15 N·m (11 lb ft).
  6. Install the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
  7. Connect the battery negative cable to the battery. Tighten
    Tighten the battery negative terminal bolt to 15 N·m (11 lb ft).

Posted on Nov 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery was changed, now car won't start key stuck in ignition.


Can you turn the key ? ON - OFF Who changed the battery ? When you change a battery you need to use an external battery supply till new battery is in , so this doesn't happen ! You may need to have it towed to the dealer to have a module reset done ! Battery Disconnect or Replacement Problems

Aug 07, 2015 | 2011 Chevrolet Cruze

1 Answer

I have a 98 corvette I changed the battery and the car won't turn over


Why did you change the battery? Was the car running before you changed the battery? Did you remove your negative cable first before your positive cable on your battery? I ask cause sometimes people ground the positive cable to ground when they remove their battery and blow a fuse or relay. If they are good check your battery and starter you might have a loose cable. Let me know how you make out.

Oct 16, 2014 | Cars & Trucks

1 Answer

Change battery


Step 1 : Igniton key off.
Step 2 : Open the Bonnet.
Step 3 : The battery is on your left hand side.
Step 4 : Remove the fastners and replace the battery.

No reset in computer required. The computer can handle your battery change act ! :-)

Dec 23, 2013 | 2010 Ferrari California

1 Answer

I HAVE A SURESAFE20ES; BATTERY IS DEAD; WHERE DO I OPEN TO CHANGE THE BATTERY? IT'S PRETTY URGENT


You need to charge the battery...not change it. If you can get a charge into it try a factory default code like 7777 to try to reprogram the safe.

Jul 04, 2012 | Cars & Trucks

1 Answer

My 2002 s600 is not starting after I changed the dead battery


Which battery did you change? There are two batteries installed on your vehicle. There is a battery in the trunk on the right side which is called the systems battery which supplies power to the electronics of the vehicle and the second battery is under the hood near the bottom of the windshield. The battery under the hood is the starter battery. Check and/or replace that battery and let me know what happens.

Feb 19, 2012 | Mercedes-Benz Cars & Trucks

1 Answer

How do you change the battery?


I think it takes a GM type GROUP 75 battery. If its like a Sebring? After you take the left wheel off and the splash shield, its easy.

Dec 10, 2009 | 1998 Plymouth Breeze

1 Answer

Battery light comes on changed battery still doing it alt. 1 year old


most likeley needs an alternator.not very easy to chang on that vehicle. hope this helps, good luck.

May 25, 2009 | 2003 Ford Escape

2 Answers

How do i change my car battery without losing my radio.


You need to keep a supply to it. You can buy various devices that plug into your cigar lighter. The quite simply have one of these square 9 volt radio type batteries in them. This keeps power on while changing battery. You could easily make something up with one of these batteries and a couple of leads going to the terminals after loosening the bolts. Be careful though and make sure your wires are secure so the do not come off while wrestling with the battery.
Cheers John

Dec 18, 2008 | Volkswagen Passat Cars & Trucks

Not finding what you are looking for?
2000 Chevrolet Monte Carlo Logo

554 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...