Question about 2006 Mazda 6

1 Answer

My security indidcator light is flashing every 2 seconds when my car is shut off. It stops flashing once I turn the vehicle on. How can I get it to stop flashing when the vehicle is off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 394 Answers

Hi,
The security flashing is an indicator that your security system is armed and working.
It helps deter thiefs when they see the flashing light. They know if they try and break in your car the alarms will go off.
It is a good thing the red light is flashing.
Hope this helps ease your mind.
Wayne

Posted on Nov 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to program my key to 98 ford explorer


for Ford keys (1996 -early 1998 Ford, Lincoln, Mercury)

If you want to initiate a new master key....

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position. The security light on the dash will flash for fifteen minutes.


2. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder OFF and then back to the ON (RUN) position. The security light on the dash will flash for fifteen more minutes.

3. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder to OFF and then back ON (RUN) position. The dash will flash for fifteen more minutes.

4. After the security light stops flashing the third time, the new key has been programmed into the vehicles computer and will operate the car. It has replaced ALL the previous electronic key codes and is the ONLY key programmed into the vehicles computer.
If you want to add a key....


1. Insert an existing key into the ignition cylinder.


2. Turn the ignition cylinder to ON (RUN) and back to OFF.

3. Remove the existing key and, within 15 seconds, insert the new key and turn it to ON (RUN).

4. The security light will light up for two seconds to indicate success in programming the key into the vehicle.

5. Don't attempt to start the vehicle with any key for at least 1 minute.
<HR>On-Board Programming Method "C"


for Ford keys (Later 1998-newer Ford, Lincoln, Mercury)

If you want to initiate a new master key....

1. This requires that the vehicle be connected to special dealer equipment. There are two ten minute delays involved while this device erases all existing key programming and sets up the vehicle computer to accept new key codes. Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below).

If you want to add a key....


**You must have two original keys to perform this procedure. If you only have one key, you WILL have to take it to the dealer to get it programmed**


1. Insert and existing (working) key into the ignition cylinder.

2. Turn the ignition cylinder ON (RUN) and back to OFF. Ignition should stay on for at least ONE SECOND.

3. Remove the existing key and, within TEN seconds, insert a second working key and turn it to ON (RUN) and the back OFF. Ignition must be in ON for at least ONE second, but no more than TEN seconds. Remove the key.

4. Insert the new key before TWENTY seconds have elapsed and turn it to ON (RUN). Leave it the ON position for at least ONE secondand turn back to OFF.

5. The security light will light up for THREE seconds to indicate that the new key has been successfully programmed.

6. To program additional keys, repeat steps 1 through 5
As a precautionary measure for all of the above procedures, you should wait at least one minute after you have performed this until you start your vehicle.

Dec 10, 2016 | 1998 Ford Explorer

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

I called myself programming the new keys for my pt cruiser, but,it didnt take. At first it would start and run for a few seconds, now it wont turn over.what did I do wrong and how can I fix this?


Takes the master key to get it started again. The security gives you 3 tries to get the vehicle started, after the third time, it kills the starter.
2002 Chrysler PT Cruiser Note: You must have two valid keys to add a new key to the system.
1. Insert the first valid key into the ignition switch. Turn the ignition switch to the
ON/RUN position for at least three seconds, but no longer than 15 seconds.
Then, Turn the ignition switch to the LOCK position and remove the first key.
2. Insert the second valid key into the ignition switch. Turn the ignition switch to
the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound.
In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch
to the LOCK position and remove the second key.
3. Insert the new key into the ignition switch. Turn the ignition switch to the
ON/RUN position.within 60 seconds. After 10 seconds, a single chime will
sound. In addition, the Vehicle Security Light will stop flashing. To indicate that
programming is complete, the Vehicle Security Light will turn on again for
seconds and then turn off.
The new key is now programmed. The Remote Keyless Entry transmitter will
also be programmed during this procedure.
Repeat this procedure to program up to eight keys.

Oct 09, 2016 | Cars & Trucks

3 Answers

How do i reset the alarm on my 2003 Chevy Trailblazer...I can't stay my truck.


Hello Narisol,


Excerpt from the 2003 Owners Manual.


Passlock

Your vehicle is equipped with the Passlock theft-deterrent
system. Passlock is a passive theft-deterrent system.
Passlock enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder
is tampered with, the fuel system is disabled and the vehicle
will not start. During normal operation, he SECURITY light
will turn off approximately five seconds after the key is turned to
RUN. If the engine stalls and the SECURITY light flashes,
wait about 10 minutes until the light stops flashing before trying
to restart the engine. Remember to release the key from START as
soon as the engine starts. If the engine does not start after
three tries, the vehicle needs service. If the engine is running and the
SECURITY light comes on, you will be able to restart the engine
if you turn the engine off. However, your Passlock system is not
working properly and must be serviced by your dealer. Your vehicle is not protected by Passlock at this time. You may also want to
check the fuse. See Fuses and Circuit Breakers on page 5-85.
See your dealer for service. In an emergency, call the M
Roadside Assistance Center. See Roadside Assistance Program on
page 7-5.


Excerpt from the 2003 Owners Manual.

Testing the Alarm The alarm can be tested by following these steps:
1.
From inside the vehicle, Iower the driver's window and open
the driver's door.
2.
Activate the system by locking the doors with the power door
lock switch while the door is open, or with the remote keyless entry transmitter.
3.
Get out of the vehicle, close the door and wait for the SECURITY light to go out.
4.
Then reach in through the window, unlock the door with the manual
door lock and open the door. This should set off the alarm. When
the alarm is set the power door unlock switch is not operational.
If the alarm does not sound when it should but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To
replace the fuse, see Fuses and Circuit Breakers on page 5-85.
If the alarm does not sound or the headlamps do not flash, the
vehicle should be serviced by your dealer.

Jul 26, 2016 | 2003 Chevrolet TrailBlazer

1 Answer

Security light flashes


Antitheft or Security system failure is a common problem on GM vehicles. Every time you put your key in the ignition, the vehicle's security system reads the signal from your key to make sure it is OK to run. When it recieves the "correct key" signal, the security system allows the starter to turn over, and/or the fuel injectors to function and your car works like it normally does every day. If you were to use a different key, or try to hotwire it, the system would shut down these parts of your car, thus making the vehicle completely immobile. This is GM's way of preventing vehicle theft. The problem is that the system is known to fail quite commonly. It has been failing consistantly for around 30 years. When it fails, two things can happen. First, you turn the key and nothing happens at all. Lights work, radio works, windows work... just not the starter that you need to start the vehicle. This is a "starter immobilizor". Second, you turn the key and the vehicles starts just fine, but then stalls in 2-5 seconds. This is a "fuel immobilizor". It literally cuts off the fuel injectors and stalls the vehicle to immobilize it. These are normally, but not always followed by a light on the dash that says SECURITY or ANTITHEFT. These lights are to inform you of the system's failure to collect the information it needs from your key to the computer. If your security/antitheft light is on, odds are you will be stranded soon, if not already. Remember that the security system controls the security light. If the system is failing, the light may never warn you of the failure. There is a lot of info on this site that you can read up on. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Jul 21, 2014 | 2002 Saturn VUE

1 Answer

Secureilock error code 13 on 2007 ford expedition. I am having problems remote starting my expedition.


Securilock problem for your remote start? Check when you try to start it, if the security light is flashing fast it is probably the PATS (security system) bypass. To reprogram it you will need two keys. First insert the first one and turn it to the run position. When the security light shuts off insert the second key and turn it to run. Once the light has gone off the second time pull the key out and hit the start button on the remote start fob, this all has to be done in 10 seconds. The vehicle will start, shut it off and try it again. If it doesn't start look to see if the security light is flashing fast again if it is the bypass needs to be replaced. If the light isn't flashing fast and it still doesn't start it should be honking at you or flashing its lights, count these then look in your manual it will tell you what is wrong. If none of these work let me know and I will help you. You can also check out my profile I have a tip that is about remote starts.

Good Luck

Dec 26, 2010 | 2007 Ford Expedition EL XLT

1 Answer

Starter turns but no ignition, PK3 M security, the problem is intermittent and does not cause a problem with every start. So far I have been able to get it started after several attempts with differing...


is your security light in dash flashing if so try to start let off key but do not cut off leave key on so all your dash lights are on let vehicle set for at least 15 mins. flashing security light should stop flashing once it stops flashing start vehicle sounds like it has tripped security

Mar 16, 2010 | 2002 Pontiac Grand Prix

1 Answer

96' sunfire changed engines 2.2 starts dies theft light comes on


The problem is the new PCM you installed does not have the correct VIN number of your car.
You may be able to relearn the VIN using the preceedure below, however, there is no gaurentee it will work. You may have to have a dealer reset the VIN for you by way of a scan tool.

1) Instert key into ignition and rotate to run position (do not try to start engine)
2) Leave the key in the run position for 10 minutes until security light stops flashing.
3) Turn ignition key to off position for 10 seconds ( no more, no less)
4) Turn ignition to run position again for 10 minutes until security light stops flashing and repeat step 3 and 4 for (1) more cycle.

The process is a security verification step for the VTD system. ( Vehicle Theft Deterent)

Give it a try, let me know.
Regards,

May 04, 2009 | 1996 Pontiac Sunfire

1 Answer

Program 2002 Mercury Sable Key


For convenience, I'm also including a list of other vehicles that these instructions apply:
Ford Contour ‘98–up
F-150 ‘98-up
Ford Crown Victoria ’97-up
Ford Escort 99-up
Ford Excursion ‘00-up
Ford Expedition ‘98–up
Ford Explorer ’98-up
Ford Focus ‘00-up
Ford Mustang ’96-up
Ford Ranger ’98-up
Ford Taurus ’96-up
Ford Windstar ’98-up
Lincoln Continental ’98-up
Lincoln LS ’00-up
Lincoln Mark VIII ’98-up
Lincoln Navigator ’98-up
Lincoln Town Car ’98-up
Mercury Grand Marquis ’97-up
Mercury Mountaineer ’98-up
Mercury Mystique ’98-up
Mercury Sable ’96-up
NOTE: These instructions may apply to more or less vehicles than those listed above. I cannot confirm that these procedures work for every year and model listed. See your dealer if to confirm this.
On-Board Programming Method "B" for Ford keys (1996 -early 1998 Ford, Lincoln, Mercury)
If you want to initiate a new master key.... 1. Insert new key into ignition cylinder and turn it to the ON (RUN) position. The security light on the dash will flash for fifteen minutes.
2. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder OFF and then back to the ON (RUN) position. The security light on the dash will flash for fifteen more minutes.
3. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder to OFF and then back ON (RUN) position. The dash will flash for fifteen more minutes.
4. After the security light stops flashing the third time, the new key has been programmed into the vehicles computer and will operate the car. It has replaced ALL the previous electronic key codes and is the ONLY key programmed into the vehicles computer.
If you want to add a key.... 1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within 15 seconds, insert the new key and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming the key into the vehicle.
5. Don't attempt to start the vehicle with any key for at least 1 minute.
On-Board Programming Method "C" for Ford keys (Later 1998-newer Ford, Lincoln, Mercury)
If you want to initiate a new master key.... 1. This requires that the vehicle be connected to special dealer equipment. There are two ten minute delays involved while this device erases all existing key programming and sets up the vehicle computer to accept new key codes. Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below).
If you want to add a key.... **You must have two original keys to perform this procedure. If you only have one key, you WILL have to take it to the dealer to get it programmed**
1. Insert and existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (RUN) and back to OFF. Ignition should stay on for at least ONE SECOND.
3. Remove the existing key and, within TEN seconds, insert a second working key and turn it to ON (RUN) and the back OFF. Ignition must be in ON for at least ONE second, but no more than TEN seconds. Remove the key.
4. Insert the new key before TWENTY seconds have elapsed and turn it to ON (RUN). Leave it the ON position for at least ONE second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate that the new key has been successfully programmed.
6. To program additional keys, repeat steps 1 through 5
As a precautionary measure for all of the above procedures, you should wait at least one minute after you have performed this until you start your vehicle.

Mar 27, 2009 | 2002 Mercury Sable

2 Answers

Security light flashing


Take the Original Ignition key out to the car. Get in it and turn the key on. Every light should light up like your going to start it. The factory security light will flash. Leave the ignition on until it stops flashing. Should take about 10-15 min to do it. once it does, shut the key off and then turn it over to start the car.

Aug 04, 2008 | 1998 Chevrolet Lumina

Not finding what you are looking for?
2006 Mazda 6 Logo

956 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...