Question about 1989 Toyota Camry

1 Answer

I need to replace my clutch - 1989 Toyota Camry

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

Click on this link.It has good description with good pictures and diagrams.http://www.toyotanation.com/forum/showthread.php?t=216535 -----

Posted on Nov 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch and engine check light plus clutch got eaten up in 2 weeks time


If ur have replace ur clutch but the check light still on it mean your CO sensors need to clean or replace.

Jun 17, 2016 | Nissan Cars & Trucks

2 Answers

Hyundai. Tucson, 59 plate' clutch slips at high speed when changing gear


check /replace clutch cable or replace master cylinder. If the clutch has not been replaced it may need a clutch kit as the indications are that the pressure plate is weak ( worn clutch plate or from overheated clutch)

Feb 10, 2015 | Hyundai Tucson Cars & Trucks

1 Answer

Transmission slipping


This normally means your clutch is worn down and needs replacement. Much less likely is that the clutch pedal travel needs adjustment.

Replacement of the clutch requires removal of the gearbox and is much easier with a shop hoist. I'd recommend replacing the pressure plate assembly as well.

Jul 31, 2012 | 2003 Toyota Corolla

1 Answer

I recently purchased a 2003 hyuandai tiburon GT with 171k miles on it i was on the interstate doing 80 mph in 4th gear at around 6k rpm when my clutch pedal dropped back into the floor board and just...


hmmm... 80mph @6000 rpm is not normal. you are needing a lot of power to produce 80mph. it seems clutch assembly needs replacement. clutch assembly includes clutch disc, fly wheel, and release bearing. might as well check your clutch master if the vacuums are still working properly. this might be the culprit to the stuck up clutch pedal.

after replacing the clutch assembly, you can reach 80mph @ 4000-4500rpm

Aug 06, 2011 | 2003 Hyundai Tiburon

1 Answer

Replaced master and slave clutch cylinders but


if you replace and shure to make a good bleed on clutch fluid, then replace clutch disc

Jul 27, 2010 | 1991 Toyota 4Runner

2 Answers

Clutch needs adjustment


as the clutch wears the "free pedal" is reduced ... its easy to adjust "free pedal" and important to do so .. when there is very little or no free movement above where the clutch engages/disengages then the clutch starts to wear rapidly ... if there are no other symptoms like clutch chatter, slipping or noise then the clutch plate likely has some life left if it is adjusted properly and promptly ..

Feb 22, 2010 | 1994 Nissan Pickup

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

Hi i have a peugeot 406 2.0 hdi 1999, when i get in the car the clutch pedal is on the floor and i have to pump the pedal for a couple of minutes, then it is ok to drive. any ideas what is wrong with it?


The clutch acting system is hydraulical, (clutch hydraulic system).
Your clutch pedal master cylinder is weak, and needs to be replaced or repaired by gasket kit replacement. Also the clutch slave cylinder can be used, and needs to be repaired (by gasket kit replacement), or replaced. The clutch system must be bled after carrying out work on the hydraulic clutch mechanism.

Dec 09, 2009 | 2006 Peugeot 504

1 Answer

Clutch repair 2005 VW Chico


You need to empty the engine from all fluids, tehn remove air filter and other parts, mount your Golf on a bridge and remove the clutch pressure plate assembly mounted on a side of the engine.

You will need special tools to align and mount the new pressure plate, and you will need to follow a procedure to reinstall the clutch without removing the transaxle.

Replacing the clutch is not an easy task for a beginner, if you do it yourself, get the haynes manual with the complete illustrated procedure.

After replacing you will have to adjust the clutch. See CLUTCH REPLACEMENT PROCEDURES.


Feb 17, 2009 | 1997 Volkswagen Golf

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...