Question about Chevrolet Malibu

Open Question

How to remove rear bumper cover on a 2007 malibu

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
eitan
  • 291 Answers

SOURCE: remove the rear bumper

Removing Prowler Rear Bumpers First remove the four 10 MM bolts holding the trans cooler and drop it down. Support it by attaching one bolt to the lower hole on the cooler frame. This will keep the weight off the lines. This takes two min. and allows easy removal of the elect. lines. Then remove the four bolts on each bumper. The bolts are 13MM and 17MM. You will need a ratchet, sockets, extension and a 13MM open end wrench. If you remove the rear bumpers, you should replace the rear pan with one of the aftermarket ones otherwise you will have big holes staring at the people behind you. Go to prowleronline.com and check the vendors for a couple of options. Maybe you are removeing them to paint and reinstall. Look at this link for some options .. Mine is the 7th post down. http://www.prowleronline.com/ubb/Forum1/HTML/014949.html Hope this helps.

Posted on May 15, 2008

Ad
  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

abauto
  • 353 Answers

SOURCE: need step by step instructions on how to remove a

Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Posted on Nov 12, 2009

  • 10865 Answers

SOURCE: remove 2007 jeep compass bumper cover

Hello, I can assist you. Begin by rounding up the necessary tools:

7mm socket and ratchet
7mm wrench
10mm socket
screw driver or panel removal tool (for push rivets)

Now go to the following site and take a look at the step by step instructions and pictures which does a nice job of explaining this entire job. Thanks for using Fixya!
http://www.jeeppatriot.com/forum/showthread.php?t=6291

Posted on Nov 18, 2009

MNfisherman
  • 11896 Answers

SOURCE: how to remove the rear bumper cover on a town and

From underneath the vehicle. The bumper is held on by 4 bolts and nuts. (2 on each end) Remove the nuts and bumper will pull off. Then you can pry off bumper cover to once entire bumper is off.

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing rear bumper cover for 2007 uplander


Lift the tail gate. There are clips or screws along the top edge. Remove this. The clips all you do is pull the center pin with a panel tool or pliers then the rest will come out. Then you will need to remove the clips holding the rear side of each of the back wheel wells in. Under that will be more clips, screws or bolts that hold the side edges of the bumper cover on.

Aug 19, 2016 | 2007 Chevrolet Uplander

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

1 Answer

Removing rear bumper cover on 2007 Chevrolet Impala?


Most dents can be popped or tapped back out, provided it has not crumpled or creased the metal.


---------------------------obd2express.co.uk

Dec 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

How do you replace a bumper bar ....do you need a whole new skirt


Bumper bar? Skirt?
There is a bumper reinforment behind the bumper cover.
Front or rear???
Either way there are some plastic retainers on top. You may need to remove a grill which would have some sort of retainer. The retainers usually have a center section that prys up some and the retainer will then pull out.
There should also be some retainers on the undersides of the bumper covers.
There is just about always a bolt going up through the bumper cover into the rear quater panel or front fender right in the wheel well edge. Sometimes there is a guide that the cover slide onto as well. You may need to remove the tail lights. There will be nuts on the inside behind the trim panels or the headlights. they usually have some clearly seen bolts holding them in (about 4 give or take)
Unplug any lights and they can usually be left in the bumper cover.
Then off comes the cover.
From there you may find a styrofoam pad. Don't lose that as it helps the cover keep its shape in the heat. And either the reinforment will be bolted or welded to the frame rails.

Sep 06, 2011 | 2007 Toyota Camry

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

I need info on how to replace the headlamp bulbs on my 2008 Chevy Malibu, can you help.


The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.
  1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
  2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
  3. You will also need to remove some of the fasteners at the front of the inner wheel well.
  4. The Front Bumper Fascia is the plastic cover over your front bumper.
  5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.

Oct 27, 2009 | 2008 Chevrolet Malibu

1 Answer

I want to fit a towbar to my ford focus hatch 2008 model. What is involved in removing rear bumper Regards Brian Lamb


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Oct 27, 2009 | 2007 Ford Focus (3 Door) Hatchback

2 Answers

2007 buick lucerne has water leaking into the spare tire wheel well. please advise


Remove trunk trim and covers , close trunk and wet car now look for leak source.

Jun 16, 2009 | 2007 Buick Lucerne CXS Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...