Question about 2004 Chrysler Crossfire

Open Question

Where is the OBD 2 port on a 2004 Chrysler Crossfire? I cannot locate it.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: cant find OBD port on a 1994 Chrysler Newyorker

it under the dash on drivers side right in front of the gas pedal its blue with 6 plug in ports its the only one there

Posted on Jul 30, 2009

  • 580 Answers

SOURCE: 2004 chrysler crossfire resetting service light

Disconnect negative battery post for 30 seconds & reconnect. This action will reset the car's computor & remove the light.

Posted on Jan 08, 2010

chargerhp
  • 813 Answers

SOURCE: where is the low pressure side port located for

as you are standing in front of car on left side behind air filter is a receiver alum canister with a cap on top this is the high pressure side just below the receiver and under the firewall you will see a cap this is the low pressure or fill valve

Posted on Oct 27, 2011

Milleniumboy
  • 106 Answers

SOURCE: 2004 Chrysler Crossfire won't start. Drove in

Hello,

The battery could be low, also clean cups around battery terminals, ensure that air filter is not clogged. If problem persists, it could possibly be the alternators. :)

Posted on Apr 05, 2010

ftw1952
  • 10319 Answers

SOURCE: 2004 Chrysler crossfire stuck in park and cannot

remove the shift solenoid by the shift cable inside the vehicle. then wire up the solenoids lock to the shifter to tow

Posted on Jun 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Obd2 connector locations


Hi Curtis, I'm glad to help! OBD 2 reffers to the type of system you have. But if your looking for the diagnostic port. The Data Link Connector is under the dash on the drivers side very close to the knee booster cover below the steering column. Hope this helps and have an awesome day Curtis.

Apr 27, 2014 | 2007 Chrysler 300c AWD Sedan New Cars

1 Answer

Someone that knows about cars not cameras


They are located in the intake valley of the Engine .their are two of them bank 1 and bank 2 .

Aug 06, 2012 | 2004 Chrysler Crossfire

1 Answer

Just fueled up 93 octane. drove approx 1/2 mile to work. started the car, check engine light came on and runs extremely rough and stalls. could it be the fuel and how do i check it. 2004 chrysler...


I would suspect the fuel is the problem, most likely water is in the fuel, but get the codes read to see what fault shows up that turned on the check engine light.

Oct 14, 2010 | 2004 Chrysler Crossfire

2 Answers

2004 Chrysler Crossfire won't start. Drove in


This is not the problem I have a chrysler crossfire and experienced the same problem there is some good news if it frequently stops working for no reason the problem is most likely the RCM module has a shortage in it I fixed my crossfire and 3 others buy repairing the RCM its easy and simple any question you can email me I can give you a easy walk through to fix the problem and avoid paying hundred at the dealership it shouldn't take no more than 15 minutes to fix DIY!!

Apr 05, 2010 | 2004 Chrysler Crossfire

2 Answers

2004 chrysler crossfire resetting service light


Disconnect negative battery post for 30 seconds & reconnect. This action will reset the car's computor & remove the light.

Jan 07, 2010 | 2004 Chrysler Crossfire

1 Answer

Cats are rattelling need good after market set


there are lots of good aftermarket exhaust systems, but will all be cat back systems, you may be able to take it to a muffler shop and have them put on universal high flow cats, which would be a lot cheaper, being an OBD II vehicle. the cats are required, and O2 sensor eliminators for the sensor after the cat are NOT recommended on chrysler vehicles.

Oct 24, 2009 | 2004 Chrysler Crossfire

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

Related Topics:

1,271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...