Question about Toyota Land Cruiser

1 Answer

Hi Im looking for a parts or service manual to see what parts are on the end of the cam shaft of a 3400 V6 Perado. can you help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,267 Answers

You have not mentioned the make & model of your vehicle so I would suggest you download the appropriate manual from this site:

http://auto.manualsonline.com/np/usermanuals/mfg/toyota/car_product_list

Posted on Nov 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question?I can't find crankshaft position sensor in the mitsubishi galant 2.0 v6 24valve


look for this parts wiring in the engine bay.. unusual plug
CAS with wire leads and square plug:
dont have exact location on that motor

try looking for it at the end of the cam shaft rocker covers



26206091-dpc5zqeneklbfztn0zkuzn5h-2-0.jpg

May 27, 2016 | Mitsubishi Cars & Trucks

1 Answer

Cam shaft location 2010 tacoma v6


It should be at one end - either end - of the camshaft.

Aug 13, 2014 | Cars & Trucks

1 Answer

Mazda 323 ignition


run fault codes and look for cam/ crank position sensors faults. check that the cam shaft is turning ( broken timing belt/chain). Check that the immobiliser is operational.

Feb 14, 2014 | Mazda Cars & Trucks

2 Answers

I have a 96 camaro and I need to replace my carrier bearing. Where can I find one?


I am not sure your car has a carrier bearing, but if it did it would be located on the drive shaft between the transmission and rear end of the car.

Apr 22, 2013 | 1996 Chevrolet Camaro

2 Answers

My toyota 3C turbo diesel engine the turbo compressor is flooding of oil . I can.t trace where it is coming from That is why I am searching service manual for this turbo charger. 12ct


Hi,

If your turbo housing is getting flooded with oil the it can only come from the shaft seal on the inside of the turbo.

You will need to remove it and replace the shaft seal.

Jun 19, 2010 | Cars & Trucks

1 Answer

Cam shaft sensor


You always need to check the wiring system when you get a code and not just throw parts at it,I'm sorry this happened to you.

Dec 23, 2009 | 1996 Dodge Grand Caravan

1 Answer

Need diagram or spec to set cam position


if you look at the back edge of the camshafts you will see a slot, this slot is off center on the shaft end, you are supposed to use a special tool and turn each shaft to where that slot is flat across the cylinder head, then insert the tool (flat piece of steel) into the slots, the tool hold the cams in place while you reset and put on the belt. You can find this diagram in any Haynes or Chilton manual, availiable at your local parts store, autozone should be able to print it out for you from AllData for free, hope this helps, let me know

May 28, 2009 | 1995 Ford Contour

2 Answers

92 toyota camry v6 do they have 2 heads or just 2 cams


That is possible if it is not dual overhead cam if it is single overhead cam that would be right.

Mar 04, 2009 | 1992 Toyota Camry V6

1 Answer

I have a coolant leak coming from the front of the engine. looks like it is leaking around the cam shaft pulley. The vehicle is a 2001 Nissan Frontier v6


Sounds like either the water pump or the thermostat housing. The water pump has a small hole in the bottom where the shaft comes through, when the water pump gets worn it will leak here so you know to replace the pump. The thermostat housing will be at the motor end of the upper radiator hose where it attaches to the motor. Hope this helps.

Aug 11, 2008 | Nissan Frontier Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...