Question about 2001 Saturn L-Series

Open Question

How to remove power window switch from center console

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 84 Answers

SOURCE: 1988 Mercedes Benz - 300E , want to replace window switch

Hello, To the rear of the wood grain where the switches are, you should have a small piece of carpet that you just pull up and get it out of the way. You should see 1 screw. Remove the screw and gently pull up on the back of the wood grain. Now you will be able to change the switch.
I hope this helps.
CYA, Gator241

Posted on Feb 07, 2009

Ad
GM Elec
  • 1000 Answers

SOURCE: need instructions on how to remove center console to access electric window switch.

Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.

  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

Posted on May 04, 2009

motor1258
  • 6674 Answers

SOURCE: replacing window switch in console

Those screws your probably having trouble with, require seats removed to get at them. Sorry.

Posted on May 12, 2009

action t
  • 8 Answers

SOURCE: 1993 Volvo 850 How do I remove the Center Console

if you cant find any plastic that pops out and has screws underneath carpet inside center console if any, try pulling the switch itself and or assembly out. hit contacts with an eraser. and your favorite stuff. get a good manual.

Posted on May 24, 2009

hdsoft
  • 80 Answers

SOURCE: bulb on center console luminating power window

Bulb's are not replacable.Have to replace switch assembly and have cluster rebuilt.

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and replace window switch from console in 99 Pontiac Sunfire GT convertible?


Do you have a convertible ? For convertibles only, refer to Console Replacement. If you don't have a convertible just Use a flat-bladed screwdriver in order to pry the power window switch outward.
Disconnect the power window switch wire harness.
Remove the power window switch.

Feb 08, 2017 | 1999 Pontiac Sunfire

1 Answer

How to chang heater cor inP/T croser


It is pretty involved requiring discharging/disconnecting the AC, Dash board and other components. If you are up to it I found these step by step on the Autozone web site.

As seen on autozone's web site (/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f8075b324)

Instructions -

Before servicing the vehicle, refer to the Precautions Section.

Remove the A/C refrigerant using the approved equipment.

Drain the cooling system.

Disconnect the negative battery cable.

Remove the instrument panel by removing or disconnecting the following:

The left and right A pillar trim moldings using a trim stick

The front power window switch

The center bezel retaining screw

The Heating, Ventilation, and Air Conditioning (HVAC) control knobs

The center bezel using a trim stick

The top cover retaining screws and pull it rearward to remove

The HVAC control unit from the instrument panel

The retaining screws from the upper and lower steering column shrouds

The left lower instrument panel bezel

The steering column wire connectors

The steering column

The brake pedal support bracket

The left side instrument panel end cap from the wiring connectors

The rear power window switch from the console and pull the parking handle all the way up

The auxiliary power outlet wire connector

The center console

The glove box assembly

The right side instrument panel end cap

The 5 right side instrument panel wire connectors

The instrument panel from the vehicle, with the help of an assistant



Remove or disconnect the following:

The heater hoses from the heater core

Reposition the vehicle speed control servo, if equipped

The suction and liquid lines from the evaporator

The drain tube

The A/C vacuum harness connector

The defroster duct from the heater A/C unit housing

The heater A/C unit housing from the vehicle

The heater core from the housing





To install:

Install or connect the following:

The heater core to the housing

The heater A/C unit housing to the vehicle

The defroster duct to the housing

The A/C vacuum harness

The drain tube

The suction and liquid lines to the evaporator

The reposition the vehicle speed control servo, if equipped

The heater hoses to the heater core



Install the instrument panel by installing or connecting the following:

The instrument panel

The right side instrument panel wire connectors

The right side instrument panel end cap

The glove box assembly

The center console

The auxiliary power outlet wire connector

The rear power window switch

The left side instrument panel end cap

The left side wire connectors

The brake pedal support bracket

The steering column with a new pinch bolt

The steering column wire connectors

The left lower instrument panel bezel

The HVAC control unit

The center bezel

The front power window switch

The left and right A pillar trim moldings

The negative battery cable



Fill the cooling system.

Recharge the A/C system.

Start the vehicle and verify proper system operations.

Road test the vehicle and check for any rattles or leaks, repair if necessary.

Nov 16, 2014 | 2001 Chrysler PT Cruiser

1 Answer

Power window problems


i have seen the ignition switch fail not turning on all the options check for power going to the switch

Sep 07, 2012 | 1999 Saturn SL

1 Answer

I recently bought a 2002 Pontiac Sunfire SE for my grand daughter as a High School graduation gift. Now the power windows won't go up or down. What could cause this problem? Hoping it is something simple...


This is One with the Power Window SWITCH in the CENTER Console they Often Get Liquids SPILLED on them Causing them to Fail, I Would First Check for 12volts @ the Switch with KEY ON. With a Sure 12volts Going IN the Switch Check for 12 Volt going OUT, If Switch IS BAD there Will be NO 12volts Coming OUT With this Go on to Switch Replacement


REMOVAL PROCEDURE
  1. Use a flat-bladed tool in order to remove the power window switch bezel (1) from the console.
  2. Remove the electrical connection from the power window switch (2).
  3. With a flat-bladed tool release the power window switch (2) tabs, and remove the switch from the power window bezel (1) retainers.
INSTALLATION PROCEDURE \

  1. Install the power window switch (2) into the power window switch bezel (1) until fully seated.
  2. Connect the electrical connector to the power window switch (2).
  3. Install the power window switch bezel (1) to the floor console.
((((>>>All of this is Assuming that All FUSES Related to And RELAYS Related to Windows Have Been Deemed GOOD & Funktional<<<<)))
If Further HELP / SUPPORT / INSTRUCTIONS Are needed P L E A S E Dont RULE me Out as I have the Answers, Just Try to be as Spisific as Possible and I will be More than HAPPY to Help you With your Needs of Auto Repair
  1. Install the power window switch (2) into the power window switch bezel (1) until fully seated.
  2. Connect the electrical connector to the power window switch (2).
  3. Install the power window switch bezel (1) to the floor console.

Jun 15, 2009 | 2002 Pontiac Sunfire

1 Answer

1993 Volvo 850 How do I remove the Center Console


if you cant find any plastic that pops out and has screws underneath carpet inside center console if any, try pulling the switch itself and or assembly out. hit contacts with an eraser. and your favorite stuff. get a good manual.

May 24, 2009 | 1993 Volvo 850

1 Answer

Need instructions on how to remove center console to access electric window switch.


Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.
  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

May 04, 2009 | 1986 Chevrolet Corvette

2 Answers

Power window stops working... but only for 1-2 days


The same power for all windows is there at the swith control. If all others work ok then your switchs for the two problem windows are dirty. The other window work ok?

May 04, 2009 | 1999 Saturn SL

2 Answers

Rear window stuck-Convertable


does the window try to move, meaning it is stuck in its track, or does the motor not try to move the window? If the latter then look at the rocker switch on your center console that controls the rear windows. I had to replace my switches to get my rear windows working.

Jan 21, 2009 | 1992 Toyota Celica

1 Answer

Rocker switch for 94 4runner


There will be some dirt between the contacts.
The best way is to remove the centre console where the switch sits and clean the switch itself. It is an easy job, just a few screws to remove the center console.

Nov 26, 2008 | 1994 Toyota 4Runner

Not finding what you are looking for?
2001 Saturn L-Series Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...