Question about Isuzu VehiCROSS

1 Answer

JUST A DIAGRAM OF THE SERPENTINE BELT ROUTE - VehiCROSS Isuzu Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 642 Answers

The diagram can be found here.
Remove the upper fan shroud and aircleaner assemblies for easy access.
To release tension on the belt turn the tensioner pulley nut clockwise and slip the belt off the alternator pulley. To refit the belt route as shown over every pulley except the alternator, once again release the tensioner and fit the belt to the alternator. See that the belt is properly seated over every pulley before restarting the engine.

Posted on Nov 11, 2010

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: serpentine belt diagram:

if yours has the 3.8L then here is the diagram. Hope this helps
~ Zach

7f8b868.gif

Posted on Jun 16, 2008

  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

c17hydro
  • 2984 Answers

SOURCE: Cannot route serpentine belt correctly for a 1998

PLEASE DON'T FORGET TO RATE!!!

ecbee4e.gif
Serpentine drive belt routing-3.0L (OHV) engines


fd87eda.gif
Serpentine drive belt routing-3.0L (DOHC) engines

Posted on Oct 25, 2009

TDISLine
  • 1874 Answers

SOURCE: need a diagram of serpentine

The serpentine belt routing diagram for 2000 Audi A6 2.8 liters V6 engine:

a7860be.jpg
CS = Crankshaft
F = Fan pulley
Gen = Alternator
T = Tensioner
AC = Air Conditioning
PAS = Power Assisted Steering

Posted on Oct 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a copie of the serpentine belt routing on a 2007 Chrysler Sebring engine 2.7?


If you can't find the diagram, you will need to draw out the routing direction of the old serpentine belt so that you can properly route the new serpentine belt around each pulley. or you can go to any auto parts store and they should be able to give you a diagram, or go to dealer to get a red out or diagram of your old belt. Good-Day!

Jul 26, 2014 | Cars & Trucks

1 Answer

Serpentine belt diagram or route 2006 dodge stratus


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Jan 25, 2012 | 2006 Dodge Stratus Sedan

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    I need to replace the serpentine belt on my car. How do I do that?


    These instructions will help you . and also the picture below will help you more.
    1
    Locate the belt-routing diagram, printed on the fan shroud or possibly applied to the underside of the hood. This diagram shows you how to properly route the new belt, as well as identifying the location of the various pulleys, including the serpentine belt tensioner.
    2
    Move the belt tensioner off the Sable's belt using the serpentine belt tool. The tool connects to the side of the tensioner's arm and essentially acts as a handle for use in moving the tensioner. You can purchase a serpentine belt tool at most auto-part retailers.
    3
    Slip the belt away from the tensioner with your free hand and release the pressure on the tensioner with the tool. Pull the belt off the rest of the pulleys by hand and then remove it from the engine well.
    4
    Grab the old belt and new belt with one hand and put your foot through the other end of the belts. Stretch them both to their full length and check to ensure their both the same size. The old belt may have up to one-inch of extra length due to normal stretching that occurs during the belt's service life.
    5
    Wind the new belt, rib side to the pulley, around the crankshaft pulley. Consult the routing diagram and route the belt to the next pulley on the diagram. Continue to route and then check the diagram until you have the belt wound around every pulley except the belt tensioner pulley.
    6
    Double check to make sure the belt routes exactly as shown on the diagram and then move the tensioner aside once more so you can route the belt over the tensioner pulley as shown in the diagram. Move the tensioner back into place slowly and remove the tool.

    Good luck

    tgv1501_23.jpg




    Jan 03, 2011 | 1996 Mercury Sable

    2 Answers

    Trailblazer serpentine belt diagram


    Hi, first, keep this diagram around as you will need it to route the serpentine belt when you reinstall it. There may also be a diagram under the hood by the radiator.
    7e98dff.jpg Next, follow this link and watch the video that shows you how to replace a serpentine belt...
    http://www.wonderhowto.com/how-to/video/how-to-inspect-and-replace-your-car-s-serpentine-belt-267229/
    Take care

    Aug 03, 2010 | 2002 Chevrolet TrailBlazer

    1 Answer

    How do i change the serpentine belt on my 1999 chevy tracker


    First, keep this diagram around as you will need it to route the serpentine belt when you reinstall it. There may also be a diagram under the hood by the radiator.
    7e98dff.jpg Next, follow this link and watch the video that shows you how to replace a serpentine belt...
    http://www.wonderhowto.com/how-to/video/how-to-inspect-and-replace-your-car-s-serpentine-belt-267229/

    Nov 14, 2009 | 1999 Chevrolet Tracker

    3 Answers

    Diagram for 1998 lincoln continental


    There should be a diagram of the route printed on the fan shroud or somewhere else under the hood of the vehicle.

    Jul 09, 2008 | 1998 Lincoln Continental

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    842 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    yadayada
    yadayada

    Level 3 Expert

    74896 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...