Question about 1994 Dodge Ram 2500

1 Answer

Removal of automatic transmission - 1994 Dodge Ram 2500

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 172 Answers

You will need a transmission jack (buy or rent), and wheel ramps or very good jackstands. Raise the front wheels and support it properly. Set the parking brake and block the rear wheels. Disconnect the driveshaft at the rear axle. You may need to remove part of the exhaust system if it is in the way. Disconnect the shift linkage and vacuum line, and any other wires or cables. Remove the plate at the bottom of the bellhousing and unbolt the torque converter from the flex plate (flywheel). Get the transmission jack under it and then remove the transmission mount bolts and the bolts attaching it to the motor. Once you get everything disconnected, pull it back about 4 to 6 inches, it should separate from the motor and can be lowered down and rolled out.
Reverse the process to reinstall. You might want to get a shop manual that will give complete details and pictures, well worth the minor cost.

Posted on Nov 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I flush my transmission myself


Is your transmission automatic or manual ?

For automatic, lift vehicle and secure on jack stands and chuck rear wheels. Remove transmission drain plug and then remove all bolts that hole pan in place. Once pan is off, remove bolts that hold filter and remove. Installation is in reverse order. Once vehicle on ground, begin adding Trans fluid with vehicle running. Check level once it's reached normal operating temperature.

Dec 27, 2016 | Cars & Trucks

3 Answers

How to remove and replace auto transmission ?


Its a big job gave you and example for neon

Jan 18, 2015 | 2001 Chrysler Voyager

1 Answer

How to remove1995 cavalier transmission


The transmission is transversely mounted in these vehicles. The mount that secures the transmission to the body is also supporting the engine. If you want to remove the transmission without also removing the engine you will have to support the engine once you remove the transmission mount. You will need to remove the drivers side wheel, caliper, and rotor. You then need to remove the drivers side CV shaft. You will need to separate the lower ball joint in order to remove the shaft and to provide working room to separate the transmission from the engine. You need to disconnect the Shift cable (automatic) or slave cylinder (manual) from the transmission. You must separate the passengers side CV shaft from the transmission, but you do not need to full y remove it. Ensure that you do not separate the inner CV joint when pulling the transmission free from the inner splines. Remove the flywheel shield plate. If automatic transmission, unbolt the torque converter from the flywheel. Disconnect any electrical connections from the transmission. If automatic transmission, disconnect the hydraulic lines running to the radiator. Unbolt the transmission from the engine at the bell housing. Automatic transmissions will come out fairly easy...manuals you must pull back to disengage the transmission splines from the clutch disc.

Sep 07, 2014 | Cars & Trucks

1 Answer

How to remove/replace HD automatic transmission


remove both driveshaft's then transfer case and wiring, then transmission, is not a hard job but if you don't know how get someone else to do it

Aug 03, 2014 | 2002 Chevrolet Silverado

1 Answer

How many quarts of transmission fluid does a 99 Chevy Cavalier 2.0 4 cylinder transmission require?


Automatic Transmission Fluid Capacities Automatic Transmission 3-Speed Pan Removal and Replacement 4.0 quarts After Complete Overhaul 6.9 quarts When draining or replacing torque converter, more fluid may be needed. Manual Transmission Fluid Capacities Manual Transmission 4-Speed Automatic Transmission Not Owner Serviceable Complete Drain and Refill 2.0 quarts

Jun 07, 2014 | Cars & Trucks

1 Answer

How do I remove automatic transmission from 1993 Chev 2500 pickup?


TRANSMISSION REMOVAL IN STEPS.
The Drive Shaft
  • Using a 1/2-to-2-ton floor jack, lift the front of the truck and place jack stands under the frame. Once the truck is lifted enough for you to safely move around under it, begin removing the four bolts connecting the U-joint between the drive shaft and the rear axle. When you pull the drive shaft out of the tail shaft, transmission fluid will pour out of the tail shaft, so place a drip pan or oil-changing pan under the tail shaft of the transmission.
Lines And Linkage
  • If the truck is an automatic, you will need to remove two transmission lines from the passenger side of the transmission by the bell housing close to the transmission dip stick. If it's a manual transmission you won't have those lines, but you will have shifting linkage on the driver's side of the transmission. Depending on the year of the truck, the linkage is held on by either a cotter pin or locking-sleeve washer. You will also need to remove the speedometer cable. If it's an older truck, it will be a hard-cased cable similar to the emergency brake cable that threads onto the driver side of the transmission just before the bell housing. If the truck is a newer model, it will be an electrical set of wires attached to a plug on the tail shaft.

Remove From Engine
  • Remove the transmission mount bolt that holds the tail end of the transmission to the cross member on the frame. You will need to either use wood blocks or a jack to support the weight of the transmission. Take out the nine bolts on the bell housing that attach the transmission to the engine--there is one on the top center of the bell housing, two along each side of the bell housing and two on each side at the bottom next to the guide pins.
Remove From Vehicle
  • Once removed, maneuver the transmission to the rear of the truck about 6 inches until it clears either the clutch kit of a manual or the torque converter of an automatic. When the transmission is free, lower the bell housing end of the transmission down until the tail shaft is clear of the cross member.

Aug 31, 2012 | Cars & Trucks

2 Answers

How do i change a flywheel on a 1993 chevrolet k1500 pickup


remove trans bolts and slide trans back to gatn acces to fly wheel bolts u dont have to fully remove the trans.

Aug 23, 2010 | 1992 Chevrolet K1500

1 Answer

How to change transmission fluid????


Transmission Fluid Replacement Replace transmission fluid as follows:
  1. Operate engine until reaching operating temperature.
  2. Turn OFF engine.
  3. Remove the drain plug.
  4. Drain the transmission fluid into a suitable container.
  5. Install drain plug.
    • Torque to: 22-29 lb-ft. (29-39 Nm)
  6. Refill fluid to specified level.
Fluid Type Specifications 4 Speed Automatic Transmission - Nissan Matic "D"
5 Speed Automatic Transmission - Nissan Matic "K"
NOTE: Using Automatic Transmission fluid other than Genuine Nissan ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty

Jun 20, 2009 | 2004 Nissan Altima

1 Answer

Replace radiator


1. Disconnect the radiator fan motor connector. kcob130a.gif 2. Set the temperature control switch to the hot position. ecda063a.gif 3. Loosen the radiator drain plug to drain coolant. 4. Disconnect the upper and lower hose and overflow tube. 5. For vehicles with automatic transmission, disconnect the oil cooler hoses from the automatic transmission. Plug the ends of the oil cooler hoses and the automatic transmission fittings to prevent transmission fluid from spilling out and foreign material from entering. 6. Remove the radiator mounting bolts. 7. Remove the radiator and the fan motor together. 8. Remove the fan motor from the radiator. findme(''); findme(''); findme('');

May 19, 2009 | 2001 Hyundai Elantra

1 Answer

How do I swap out my radiator


DISASSEMBLY 1. Disconnect the radiator fan motor connector. kcpc006b.gif 2. Set the temperature of the heater control to the hot position. 3. Loosen the radiator drain plug to drain coolant. kddc008b.gif 4. Disconnect the upper and lower hose and overflow tube. 5. For vehicles with automatic transmission, disconnect the oil cooler hoses from the automatic transmission. kcpc003e.gif caution_icon.gif Plug the ends of the oil cooler hoses and the automatic transmission fittings to prevent transmission fluid from spilling out and foreign material from entering. 6. Remove the radiator mounting bolts. kddc014b.gif 7. Remove the radiator together with the fan motor. 8. Remove the fan motor from the radiator.

Sep 02, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...