Question about 1996 Mazda MPV

1 Answer

THE CAR DOESNT START, PUT A NEW DISTRIBUTOR, AND CRANK SENSOR AND STILL THERE IS NO SPARK TO THE PLUGS CHECKED ALL FUSES AND THEY ARE ALL FINE..

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I suggest you check your coil packs see if you have power going to them if so there is your problem

Posted on Nov 11, 2010

  • shane kellett Nov 11, 2010

    sorry didnt see the distributor part in there have you checked the timing

  • mojado35 Nov 12, 2010

    TIMING IS FINE.ALL READY CHECK. DO YOU TINK COMPUTER IS THE PROBLEM ?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2001 dodge stratus 3.0l automatic cranks but wont start not even with start fluid


check the fuel pressure and make sure you got the correct pressure

Jan 25, 2014 | 2001 Dodge Stratus

1 Answer

My 1994 100s Audi Sedan cranks fine but will not fire. Spark plugs replaced, fuel pump fuse checked, but does not fure. Can you help me?


There are several things to check first. Are you getting fuel? (If you spray starting fluid in the throttle body does the vehicle start) (if it does you have a fuel delivery problem) If you take a spark plug wire off and crank the motor (put wire near metal to make a ground) does it spark? For bad spark I would check distributor/cam sensor or crank sensor>? These componenets will make no spark. Let me know what happens? I can give you more info once you check these things, but off the top of my head I can't just guess whats wrong without more info.

Dec 01, 2010 | 1994 Audi 100

1 Answer

The engine indicator on the dash wont stay lit before the start of the car, the engine turnsover but doesnt start


There is no simple answer, there are to many variables. If you have access to a scan tool, pulling the codes should help. Without them its back to old school hunt and peck method. At this point we need to narrow down the problem. You need to test for spark.
  1. Tag and disconnect the spark plug wires from the spark plugs.
  2. Remove the spark plugs and install the spark plug wires to each spark plug.
  3. Ground (do not hold spark plug) the spark plug; check if spark occurs while engine is being cranked.
Crank the engine for no more than 2 seconds at a time to prevent flooding the engine with gasoline.
If you have spark, You will want to make sure you have fuel injector pulse, along with fuel pressure. If you have spark ..simply spray some starting fluid in through the air filter and hold the gas pedal to the floor and crank it over while spraying. If it fires up, you know it is fuel related( fuel pump, regulator, or ECM if no injector pulse) . If you have no spark then look at ignition coil connection and trace through to the distributor( if equipped ). The crank shaft sensor has a tendency to fail on these as well. This should give you a few things to test and check to start you on your way to narrowing it down. If you have no spark then look at ignition coil connection for power and trace through to the distributor( if equipped ). If it is DIS( no distributor). It may be the Crank sensor or the ECU. The crank shaft sensor has a tendency to fail on these as well.
The ECU uses the signal sent from the Crank sensor to trigger the spark and fuel injectors. ( make certain you have checked all fuses)

Nov 14, 2010 | 2002 Mitsubishi Lancer

2 Answers

I have no spark in my 1987 honda accord i have replaced the coil and a new distributor also the main relay fuse is good as well as all the other fuses look good it turns over just fine seems to want to...


I would check the crank sensor located on the bell housing. This senses that the engine is turning and allows a spark to be produced. No sensor no spark.

Oct 09, 2010 | 1987 Honda Accord

1 Answer

1989 toyota land cruiser.driving on highway engine died.turns over good but wont start.has a full tank of gas.put in new battery and altenator a few weeks ago,been running fine.checked the fuses and found...


Hi.

Re:new battery and altenator
If engine turns over battery and altenator are OK.

Re:checked the fuses and found a few were blown.
Effectively those may be symptoms of a wiring problem. If a job had been carried recently, undoing and re-connecting the wires to access the part(eg. alternator) may have contributed to the problem.

Check all fuses, with attention to fuel pump fuse. Check the connectors to fuel pump, eventually read volts at pump and nsure that fuel is circulating
Check air intake and connectors to air intake sensors (MAF sensor), check connection to crank sensor and O2 sensors.

The blown fuses may also have been incidental. If you did not find anything, troubleshooting must proceed as usual, checking distribution, fuel pressure, and then factors that can affect the ignition.

Remember that after a prolonged and failed attempt to crank the vehicle, the cylinders will be flooded and the car will no start (wet plugs- no spark).

Check if there is spark on all cylinders. This can be done removing one by one the spark plugs wires and putting them near to the engine block while someone else try cranking. You will see the spark.
If there is no spark, then you have a coil/distribution problem. test coil by reading volts in and impedance (coil must not be open). I think this engine is not distributorless. Check distributor cap and wires. If you have disconnected spark plug wires after the problem, also ensure that wires are connected in right order.

Once you are sure that there is spark, check fuel delivery and engine control. This part will take longer.

I uploaded here engine control diagrams and other documents that may help.

Regards.

Sep 08, 2010 | 1989 Toyota Land Cruiser

1 Answer

I have a 1991 740 volvo, was driving down he street and it died,after i pulled over it wouldn't start


Check if you still getting fuel and sparks, two items need to keep the car running. Check fuses and fuel pump relay, if needing new relays go to the junk yard and get couple of them for nothing. Checking making sure you getting fuel and fuel pump working properly, unplug the the main coil wire to distributor so the car wont start we just want the engine just to turn over. under the hood, locate fuel filter, disconnect the line to or from it, wrap the bottom of the hose with old clothe firmly and to remember to point the house downward away from your face so it wont splash at you. and have a friend turn ignition over just like starting, see if the fuel come out with good pressure. if fuses and relay check out, your crank sensor may be bad, being 91' strong possibility. crank sensor send info to computer telling to send fuel to your injectors. For sparks, make sure you plug the main wire to distributor back. pull one plug wire and get spare plug, plug it and ground the plug and have a friend turn the engine over and see if you getting sparks, do not touch the plug, big shock. No sparks, check the coil if you getting 12v, if yes, than your cam sensor is faulty. The cam sensor work just like the crank sensor but telling the computer to send sparks to the distributor. Common for older European cars, crank and cam sensor tend to become faulty after years of service due to age and heat abuse.

Aug 09, 2009 | 1991 Volvo 240

2 Answers

No spark at coil, no blown fuses, turns over fine ,but no start.


check module in distributor, check coil in top of cap also ,check the plugs to see if spark is there, if not coil is bad or module in distributor ,hope this helps thanks robert b.

Jul 05, 2009 | 2000 Chevrolet Astro

1 Answer

My 04 bmw ignition doest start


If it doesnot crank at all look for starter/starter relay/starter relay fuse. Most probably wiring coming to starter is loose, try to tighten it more (push towards starter). Also I would check antiteft system (if it is provided for your car) as some BMW have immobilizers.
If it cranks no start look for spark plugs, wires, distributor cap, coolant temperature sensor, O2 sensor, fueling system (fuel pump cutoof switch, fule pump relay, fuel filter).
Please kindly let me know if you need more information, or kindly provide me with more details to assist you better
Good Luck

Feb 01, 2009 | 2004 BMW 5 Series

1 Answer

My 1987 300zx cranks but wont start.


I had the same problem last year mine turned out to be a crank sensor I don't know if that is your problem for sure mine wouldn't send any spark from the coil to the spark plug replaced crank sensor inside distributor and fired right up the dealership called it a cam sensor my book called it a crank sensor either way its in the distributor

Dec 16, 2008 | 1987 Nissan 300ZX

Not finding what you are looking for?
1996 Mazda MPV Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...