Question about 1999 Chevrolet Cavalier

1 Answer

Power steering pump

How do you remove it to check to see why its leaking?

Posted by on

  • mikey14424 Dec 08, 2008

    i cant turn the steering wheel so i checked the fluid level and it is empty so i added some more fluid, i cant tell where the leak is coming from but i have a puddle under neath my car even when the cars not running. i started it up and tried turning the steering wheel and nothing would turn so i checked the power steering fluid and it was empty again. Please help me!!! hopefully its my lines.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Do you have the famous power steering fluid leaking and not sure where its going too? I had to replace my power steering lines as it was leaking fluid like a siv slowly at first. It was the rubber on the power steering lines leaking.

Posted on Jun 30, 2008

  • Adam Vaughn Jun 30, 2008


    To fully answer that one as i should of done before there is one bolt on the right side of the power steering pump. One on the back to loosen up the bracket and three bolts underneath the pulley. They can be accessed by spinning the open holes over them so you can wrachet them out.


×

6 Suggested Answers

  • 341 Answers

SOURCE: Power Steering Pump removal

you havr the whole bracket with pump .next you will need PS pulley removal tool take out 3 bolts same tool needed to replace pulley

Posted on Oct 20, 2008

jackiaria
  • 350 Answers

SOURCE: power steering pump leaking

Dear bigwood_84, Sat 02-21-2009 12:46pm EST (USA)

Try a can of "Bars' Leak" for power steering leaks 1st available at your local auto parts store. It's cheap and can't hurt but may fix your problem!

Advanced Auto Parts has a tool lending policy and a lot of good advice!

jack
97b12bb.jpg Please Rate This!

Posted on Feb 21, 2009

davesmith_37
  • 94 Answers

SOURCE: removing power steering pump

To replace the power steering pump, proceed as follows:

  1. Disconnect the power steering return hose from the remote reservoir or pump. Allow the fluid to drain from this hose into a drain pan. Discard the used fluid.
  2. Loosen the bracket or belt tension adjusting bolt, and the pump mounting bolt.
  3. Loosen the belt tension until the belt can be removed. On some cars, it is necessary to lift the vehicle on a hoist and gain access to the power steering pump from underneath the vehicle.
  4. Remove the hoses from the pump, and cap the pump fittings and hoses.
  5. Remove the belt tension adjusting bolt and the mounting bolt, and remove the pump.
  6. Check the pump mounting bolts and bolt holes for wear. Worn bolts must be replaced. If the bolt mounting holes in the pump are worn, pump replacement is necessary.
  7. Reverse steps 1 through 5 to install the power steering pump. Tighten the belt as described previously, and tighten the pump mounting and bracket bolts to the manufacturer's specifications. If o-rings are used on the pressure hose, replace the o-rings. Be sure the hoses are not contacting the exhaust manifold, catalytic converter, or exhaust pipe during or after pump replacement.
  8. Fill the pump reservoir with the manufacturer's recommended power steering fluid, and bleed air from the power steering system as described earlier.

Posted on Feb 27, 2009

  • 204 Answers

SOURCE: power steering pump removal 2001 sunfire gt , do

all youll need to do is remove the belt, and then you can take off the p/s pump. no need to touch the alt

Posted on Feb 04, 2010

philctr1982
  • 45 Answers

SOURCE: replace power steering pump.

  1. Disconnect the negative battery cable.
  2. If necessary, remove the air cleaner duct and the air cleaner.
  3. Remove the drive belt from the air conditioning compressor, if equipped.
  4. Loosen power steering pump belt adjustment as follows:
    1. Loosen the pivot and mounting bolts.
    2. Loosen the idler pulley locknut and turn the adjusting nut counterclockwise to remove the power steering belt.
  5. Loosen the power steering hoses at the pump and remove the bolts holding the power steering pump to the bracket.
  6. Disconnect and plug the power steering hoses and remove the pump from the vehicle.
To install:
  1. Using new O-rings, connect the power steering hoses to the steering pump.
  2. Install the power steering pump and secure it with its mounting bolts. Tighten the front and rear mounting bolts to specifications.
  3. Install the remaining components in the reverse order from which they were removed.
  4. Connect the negative battery cable.
  5. Fill the power steering system, start the engine and turn the steering wheel from side-to-side to bleed air from system

Posted on Feb 14, 2010

johnjohn2
  • 5763 Answers

SOURCE: Locate the power steering pump and lines

heres a couple of picture diagrams to help you, the most common area for a leak on these is the cooler line, this is the return line in which it is snaked in a s type shape to cool the power steering oil, these cooler line rots and leaks, so take a look at this first, its located at the bootm of the frame on the left side under the engine,hope this helps.

Posted on Apr 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Power steering leak 2002 kia sedona


To troubleshoot the issue,i suggest you to check the help link mentioned below:----

Power Steering Leaking Oil

http://technoanswers.blogspot.com/2012/11/power-steering-leaking-oil.html

-----------

Also with these i suggest you to refer these help,oinks.
Once the problem is detected,these is to replace power steering pump and fluid running line:-----

In relation to these problem there are few solved help links,i suggest you to go through the list and click the required link:-----


Power Steering going out?

http://schematicsdiagram.blogspot.in/2012/04/power-steering-going-out.html

---------------

How to Replace power steering pump on Chevy silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html

---------------

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

-------------

Power Recirculating Ball Steering Gear removal on Chevy silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/power-recirculating-ball-steering-gear.html

-----------

Chevy Silverado 2500 HD steering wheel replacing Procedure?

http://technoanswers.blogspot.in/2012/02/chevy-silverado-2500-hd-steering-wheel.html

-----------

Steering Wheel Locked?

http://schematicsdiagram.blogspot.com/2011/12/steering-wheel-locked.html

---------------

How to Remove Power steering Pressure Hose on Dodge Stratus

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

------------

How to replace power steering pump on Mitsubishi Diamante?

http://howtobyme.blogspot.com/2012/01/how-to-replace-power-steering-pump-on.html

---------------

How to bleed power steering pump on Toyota?

http://repairhelpcenter.blogspot.in/2012/02/how-to-bleed-power-steering-pump-on.html

---------------


----------

How to replace power steering pump on Toyota Land cruiser?

http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html

-----------

Steering service light ON GMC Sierra Denali?

http://technoanswers.blogspot.in/2012/02/steering-service-light-on-gmc-sierra.html

---------

Steering service light came on 2004 Pontiac Grand Prix

http://technoanswers.blogspot.in/2012/02/on-one-my-pontiac-grand-prix-relatred.html

----------

Check power steering message on Toyota?

http://schematicsdiagram.blogspot.in/2012/02/check-power-steering-message-on-toyota.html

-------

How to remove power steering pulley on 2002 Ford Taurus?

http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-steering-pulley-on.html

---------

1992 Ford Aerostar Power steering and Alternator belt routing diagram?

http://carbeltrouting.blogspot.com/2011/12/1992-ford-aerostar-power-steering-and.html

----------------

How to replace Power Steering Pump on Acura Car Models?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

--------------


How to replace Steering Linkage on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html

---------------

How to replace power steering pressure hose on mustang?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

-------------

STEERING SQUEAKS

http://alltypesofpartsreplacing.blogspot.com/2012/10/steering-squeaks.html

-----------

Steering Column Diagram For 1990 Jeep Wrangler

http://schematicsdiagram.blogspot.in/2012/07/steering-column-diagram-for-1990-jeep.html

-------------

How to replace Steering Wheel on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-wheel-on-acura.html

------------

How to replace Power Steering Pump on 1999 Acura TL?

http://howtobyme.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

-------------

These details will help.

Thanks.

Nov 28, 2012 | 2002 Kia Sedona

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

1 Answer

How to repair a power steering pump hyundai coupe 1996


SIPHON OUT POWER STEERING FLUID.USING A HAND PUMP SIPHON TYPE YOU BUY AT ANY AUTO PARTS STORES.PLACE DRAIN PAN UNDER CAR NEAR POWER STEERING PUMP CATCH FLUID WHEN YOU REMOVE POWER STEERING LINES AT THE PUMP.REMOVE DRIVE BELT.THEN REMOVE POWER STEERING PUMP.YOU NEED TO TAKE OLD PUMP WITH YOU.TAKE NEW PUMP AND OLD PUMP TO MACHINE SHOP THEY WILL REMOVE POWER STEERING PUMP PULLEY FROM THE OLD PUMP TRANSFER PULLEY TO THE NEW POWER STEERING PUMP YOU NEED TO BUY NEW POWER.STEERING HOSES O RINGS TO GO ON NEW POWER STEERING PUMP.HOSES THE OLD ORINGS WILL LEAK. THEN TAKE NEW POWER STEERING PUMP ON INSTALL IN VECHICLE THEN BLEED POWER STEERING SYSTEM.FILL POWER STEERING PUMP UP NEW FLUID.WAIT FEW MINUTES.WHEN LEVEL DROP ADD MORE FLUID UNTIL YOU GET TO FULL COLD MARK.START ENGINE 15 SECONDS SHUT OFF CHECK FOR LEAKS. NOW CHECK POWER STEERING AGAIN ADD TO FULL COLD MARK.NOW RAISE FRONT WHEELS OFF GROUND.START ENGINES TURN STEERING LEFT TO RIGHT WITH OUT STOPPING IT DO SEVERAL TIMES THEN CHECK FLUID.ADD TO THE COLD MARK DONT OVER FILL.IF FLUID LOOKS TAN HAS AIR BUBBLES IN SYSTEM WAIT A WHILE UNTIL FLUID SETTLE CHECK FLUID LEVEL.DONT DRIVE VECHICLE UNTIL STEERING FEELS NORMAL.AND IF YOU HEAR NOISES.LOCATE PROBLEM FIX BEFORE DRIVING VECHICLE.

Jan 24, 2011 | Hyundai Genesis Coupe Cars & Trucks

1 Answer

Replacement steps for power steering pump - orginal one leaking thanks


REMOVAL & INSTALLATION 2.4L Engine Fig. 1: Location of the power steering pump - 2.4L engine 87958079.gif
  1. Disconnect the negative battery cable.
  2. Disconnect and cap the power steering fluid lines from the pump.
  3. Remove the mounting bolts, then remove the power steering pump. To install:
  4. Install the power steering pump.
  5. Install the pump mounting bolts and tighten to 22 ft. lbs. (30 Nm).
  6. Uncap and connect the fluid lines to the power steering pump. Tighten the line fittings to 20 ft. lbs. (27 Nm).
  7. Connect the negative battery cable.
  8. Fill the power steering pump with fluid and bleed the air from the system.
  9. Road test the vehicle and verify no leaks.
3.1 Engine Fig. 2: Power steering pump mounting detail - 3.1L engine 86888066.gif
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt.
  3. Unfasten the power steering pump-to-engine bolts.
  4. Pull the pump forward, then disconnect and plug the pressure tubes. NOTE: Place a rag under the pressure tubes to contain any excess power steering fluid.
  5. Remove the engine mount, and remove the pump. NOTE: To remove the engine mount, support the engine with a suitable jack by the oil pan. Make sure to use a thin piece of wood on the jack pad to disperse the weight and prevent oil pan damage. To install:
  6. Position the pump and install the engine mount. Tighten the engine support-to-mount bolts to 96 ft. lbs. (130 Nm). Tighten the engine mount-to-body bolts to 49 ft. lbs. (66 Nm) and the nut to 31 ft. lbs. (42 Nm), and remove the jack from the oil pan.
  7. Unplug and connect the pressure tubes.
  8. Install the serpentine drive belt.
  9. Fill the power steering pump reservoir with the proper type and amount of fluid. Bleed the power steering system.
  10. Connect the negative battery cable and check for leaks.
prev.gif next.gif

Nov 20, 2010 | 1999 Chevrolet Malibu

1 Answer

Cant find were to put powersteering fluid


Power Steering Pump Removal & Installation 3.8L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Place a drain pan under the vehicle.
  3. Remove the accessory drive belt from the power steering pump pulley.
  4. Raise and safely support the vehicle.
  5. Remove the right front tire and wheel assembly.
  6. Remove the hoses from the power steering pump.
  7. Remove the mounting bolts and the power steering pump from the engine.
  8. Remove the reservoir and pulley from the pump if necessary.
To Install:
Power steering pump removal/installation (3.8L engine) gm-08-38-480.gif

  1. If removed, install the power steering pump reservoir and pulley on the power steering pump.
  2. Position the power steering pump to the engine and install the mounting bolts. Tighten the bolts to 25 lb ft (34 Nm).
  3. Install the pressure and return hoses to the pump.
  4. Install the right front tire and wheel assembly.
  5. Lower the vehicle.
  6. Install the accessory drive belt.
  7. Fill and bleed the power steering system.
  8. Inspect the system for leaks.
  9. Remove the drain pan from under the power steering pump area.
3.4L Engine To Remove:
  1. Place a drain pan under the power steering pump.
  2. Remove the coolant reservoir.
  3. Remove the pulley from the power steering pump.
  4. Remove the wiring harness near the power steering pump and place it out of the way.
  5. Disconnect the fluid hoses from the power steering pump.
  6. Remove the mounting bolts from the power steering pump and remove the pump.
To Install:
Power steering pump removal/installation (3.4L engine) 88008g71.gif

  1. Position the power steering pump assembly to the engine and install the mounting bolts. Tighten the mounting bolts to 25 lb ft (34 Nm).
  2. Install the wiring harness in its original position.
  3. Install the pulley on the power steering pump.
  4. Install the coolant reservoir.
  5. Fill and bleed the power steering system.
  6. Inspect the system for leaks.
  7. Remove the drain pan from under the power steering pump.
prev.gif next.gif

Sep 18, 2010 | 2000 Chevrolet Impala

2 Answers

Where is the power steering dipstick


Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools ford-08-00-401.gif

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.
Power Steering Pump (4V) and SHO To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
  6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
  7. Disconnect the pressure hose from the power steering pump and allow it to drain.
  8. Remove the power steering pump retaining bolts and the pump.
To Install:
  1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
  2. Connect the pressure hose and secure the clamp.
  3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
  4. Connect the power steering pump reservoir hose.
  5. Install the radiator coolant recovery reservoir.
  6. Install the accessory drive belt.
  7. Fill the power steering reservoir with power steering fluid.
  8. Connect the battery ground cable.
  9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.
prev.gif next.gif

Jul 22, 2010 | 1996 Ford Taurus

1 Answer

Power steering hose, leaking. How to replace power steering hose.


You will have a leak from the pump, pressure hoses or the rack. You will have to get the system washed down and inspected for the leak, most common problem is the steering rack leaking, this will leak oil onto the exhaust and cause your smoking problem, start her.


Remove the power steering pump pulley.
Place a drain pan under the vehicle. Important: Cap or plug the ends of the power steering hoses to prevent fluid loss.
Disconnect the power brake booster inlet hose from the power brake booster.

248015_2_34.gif

Disconnect the power steering cooler hose from the power steering pump.

248015_3_27.gif

Disconnect the power steering pump remote reservoir hose from the power steering pump.

248015_4_19.gif

Raise and support the vehicle. Refer to Vehicle Lifting.
Remove the power steering pump rear mounting bracket nut.
Lower the vehicle.
Loosen the accessory bracket bolts and nut. Pull the accessory bracket forward.
Remove the power steering pump mounting bolts.
Remove the power steering pump and the power brake booster inlet hose from the vehicle.
Remove the power brake booster inlet hose from the power steering pump.







Jul 23, 2009 | 1994 Toyota Corolla

1 Answer

Changing power steering pump


Power steering pump special tools

519a4ae.gif
Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Jun 28, 2009 | 1999 Ford Taurus

2 Answers

How do I repair a leaking power steering hose?


ok thees instructions that i have is for replacing the power steering pump but it has a great pic witch shows the power steering hoses i hope it helps


NOTE The following procedure requires the use of the GM Puller toolNo. J-25034-B or equivalent, and the GM Pulley Installer tool No.J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. Remove the air cleaner assembly for access.
  3. Release tension and remove the drive belt.
  4. Remove the power steering pump pulley using a suitable puller tool.
  5. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  6. Position a fluid catch pan under the power steering pump.
  7. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
    WARNING Be sure to cap all openings in the pump hydraulic system toprevent excessive fluid spillage and the possibility of systemcontamination.
  8. Remove the power steering pump from the vehicle.

    0900c15280227d22.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Pump pulley removal and installation


    0900c15280227d23.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Exploded view of the power steering pump mounting


    0900c15280227d24.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Typical power steering pump hose routing

To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secureusing the retaining bolts. Tighten the nut to 30 ft. lbs. (41 Nm).
  3. Install the pump pulley using the GM Pulley Installer tool No.J-25033-B or equivalent. Press the drive pulley onto the power steeringpump.
  4. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  5. Install the drive belt.
  6. Install the air cleaner assembly.
  7. Connect the negative battery cable.
  8. Refill the power steering reservoir and bleed the power steering system.
  9. Road test the vehicle, then check and top-off the power steering fluid.

Apr 23, 2009 | 2001 GMC Safari

Not finding what you are looking for?
1999 Chevrolet Cavalier Logo

Related Topics:

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...