Question about 1996 Chevrolet K1500

1 Answer

How do i take my passenger rear axle out of my 95 z71

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Pull the cover off the rear differential. Remove the 5/16 headed bolt that holds the differential pin in. Remove the pin. Push the axle in and remove the C clip. Then pull out the axle. Replace the pin so the spider gears don't fall out if you turn the diff with the axle out.

Posted on Nov 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the rear wheel hub on a 98 Z71


To change the bearing , you have to pull the axle. Jack the rear end up and use support jacks. Remove the differential cover, oil will come out. Put the transmission in neutral. Spin the differential until you see the bolt that holds the center pin, remove both. remove the tires. push the axle in. remove the clip one the end of the axle in the differential. pull the axle out. You can chisel the bearing out. But they do have tools that get them out.
26208027-ntpj3zzbu2souu1dk5yahwp3-4-0.gif

May 29, 2016 | Cars & Trucks

1 Answer

How do I remove a rear end from a 1993 chevy z71 4x4 1/2 ton pickup?


Fairly simple process( but not always easy,Just warning you in advance) 1. Disconnect rubber brake line from top of axle.Plug appropriately to prevent fluid loss. 2. Disconnect e-brake cables. (beside the frame on driver's side) 3. Remove shocks ( or just diconnect at either end) 4. disconnect driveshaft at axle and leave in trans (if possible) to prevent fluid loss. 5 Axle can now be removed by either removing the bolts at each end of the springs or by removing the u-bolts attaching the axle to the springs

Sep 11, 2014 | Chevrolet Cars & Trucks

1 Answer

My 95 blazer feels like something is not releasing or something is "dragging" in rear end


The greasy one has a seal leaking between the backing plate and the brakes (axle seal) which in turn will cause your brakes to grab on that wheel when you apply the brakes. Remove the axle and replace the seal. Then thoroughly clean the brake shoes and backing plate until they appear bone-dry like the other side. This should solve your problem. Make sure the rear-end grease level is full when you finish.

Mar 18, 2014 | 1995 Chevrolet Blazer

1 Answer

Need torque specs on axle nuts for dana 50 rear axle


Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Feb 19, 2011 | 1986 Ford F 250

1 Answer

Rear differential diagram


my 2003 silverado z71 rear end is stamped 8.8 on the axle is a 8.8 or a 8.5 ? 5.3l 3.73 gears g80 locker

Sep 21, 2010 | Chevrolet Silverado Cars & Trucks

1 Answer

How to remove gears from differential on a 95 mustang v6


Removal
  1. Raise vehicle and place jackstands under rear frame crossmember. Lower the hoist so that rear axle housing is at suitable working height.
  1. Remove axle housing cover from rear axle housing and drain lubricant.
  1. Perform the inspection before disassembly.
  1. Remove rear wheels, rear disc brake calipers and rear disc brake rotors.
  2. Working through cover opening, remove differential pinion shaft lock pin and remove differential pinion shaft and differential pinion gears (4215). 3fdbe2c.gif
NOTE: THIS IS FREE INFORMATION!!!!
  1. Remove rear brake anti-lock sensor . Push axle shaft inward until u-washers at button end of the axle shaft are clear of side gear recess.
  1. stb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage inner wheel bearing oil seals when removing axle shafts from rear axle housing. In addition, axle shafts should be completely removed from rear axle housing.
    Remove u-washers and pull axle shafts out of the rear axle housing. 85189ce.gif

Mar 25, 2010 | 1996 Ford Mustang

1 Answer

95 s10 and can not get it to dis engage out of 4 low


Replace the electronic controller on the front axle. Should be located toward the passenger side on the top of the axle housing. This part engages (locks) the axles, and disengages( unlocks) the axles. There is no other way to disengage your 4x.

Sep 13, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

2004 chevy z71 drive terrain, Axle


If you are talking about rear axle you will have to go to a driveline shop and have a new drive line made up. you will need a front yoke the tube and rear youke also if you lost the slider piece you will need it to and it will have to be balanced. If you need everything yor looking at about $300.00 to replace it or have one built, still half the cost of a new one. If this helped please rate.

Jun 02, 2009 | 2004 Chevrolet Silverado

1 Answer

Rear passenger wheel and brake plate axle damaged


I would, Too be on the Safe Side. An Action like this Almost EVERY time will Warp the Axle and Cause Major Problems with the Suspension. I own a 95' Silverado and had a Similar Problem.

Jan 21, 2009 | 1996 Chevrolet K1500

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
1996 Chevrolet K1500 Logo

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...