Question about 2005 Toyota Tacoma

2 Answers

Compass theremometer does not work - 2005 Toyota Tacoma

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 273 Answers

This is a very common problem with the 05-09 Tacoma. The console is very prone to internal failure. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com
There is a bunch of useful info there. Drop me an email if you have questions, thanks!

Posted on Nov 24, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 53 Answers

These are repairable, fortunately. Our company repairs them in a manner that precludes the problem from occurring again. If you re-solder the surface mount resistors, the unit will generally quickly fail again due to oxidation on the old components. We install all new components, and guarantee out work!
compass theremometer does not work - silicongeek_9.jpg
For more information, please see our website here: http://www.toyotatacomacompassrepair.com

If you have any questions, feel free to go to the website (our email address is available on every page).
Good luck!

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Compass not working on 2006 Mercury Grand Marquis


Electronic Compass The compass display and module are contained in the overhead console and are replaced as an assembly. For additional information, refer to Section 501-12 . The compass display can be turned off and on by pressing the MODE button in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W, or NW.
Inspection and Verification
NOTE: Press the MODE button to turn on the display.
  1. Verify the customer concern by operating the vehicle along roads of known direction to duplicate the customer concern with the compass.
  1. Visually inspect for obvious signs of mechanical or electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Compass module
  • Central junction box (CJB) fuse 15 (7.5A)
  • Circuitry

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Pinpoint Test A: The Compass Is Inaccurate/Inoperative
Normal Operation The compass receives battery voltage from the central junction box (CJB) through circuit 964 (DB/LG). Ground for the compass is supplied through circuit 676 (PK/OG).
    Possible Causes
  • fuse
  • circuit 676 (PK/OG) open
  • circuit 964 (DB/LG) open or short to ground
  • compass zone setting
  • compass calibration
  • compass module
PINPOINT TEST A: THE COMPASS IS INACCURATE/INOPERATIVE NOTE: Always set the zone and calibrate the compass before replacing an inaccurate compass.
NOTE: After installing a new compass, always set the zone and calibrate.
Test Step Result / Action to Take A1 CHECK THE OVERHEAD COMPASS DISPLAY
  • Key in ON position.
  • Check the overhead display.
  • Does the overhead compass display remain on after prove out?
Yes
GO to A3 .

No
GO to A2 . A2 CHECK THE COMPASS MODE
  • Press and release the SELECT switch on the overhead console.
  • Does the overhead compass display turn on?
Yes
If the compass display turns on correctly, GO to A3 . If the compass display turns on, but the heading is inoperative/inaccurate or the display indicates VAR, GO to A4 . If the compass display turns on, but it does not display all directions, or indicates CAL, GO to A5 .

No
GO to A7 . A3 CHECK THE COMPASS DIMMING
  • Turn the headlamp switch to the parking lamps ON position.
  • Does the compass display dim?
Yes
TURN the headlamp switch to the OFF position. GO to A4 .

No
TURN the headlamp switch to the OFF position. GO to A8 . A4 CHECK THE COMPASS ZONE SETTING
  • Set the compass to the correct zone for your location. Refer to Compass Zone Adjustment in this section.
  • Does the zone adjustment set correctly?
Yes
GO to A5 .

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A5 CALIBRATE THE COMPASS
  • Calibrate the compass. Refer to Compass Calibration in this section.
  • Is the compass calibrated correctly?
Yes
GO to A6 .

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A6 CHECK THE COMPASS ACCURACY
  • Position the vehicle at each of the 8 directions (N, NE, E, SE, S, SW, W, NW) and verify that the displayed heading is accurate. The vehicle must be stationary for at least 10 seconds at each direction.
  • Is the compass display accurate in each direction?
Yes
The compass is OK. REVIEW the operation of the compass with the customer.

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A7 CHECK THE VOLTAGE SUPPLY TO THE OVERHEAD CONSOLE
  • Key in OFF position.
  • Disconnect: Overhead Console C930.
  • Key in ON position.
  • Measure the voltage between the overhead console C930-1, circuit 964 (DB/LG), harness side and ground.
  • Is the voltage greater than 10 volts?
Yes
TURN the key to the OFF position. GO to A9 .

No
VERIFY the CJB fuse 15 (7.5A) is OK. If OK, REPAIR the circuit. TEST the system for normal operation. A8 CHECK THE DIMMING CIRCUIT
  • Key in OFF position.
  • Disconnect: Overhead Console C930.
  • Turn the headlamp switch to the parking lamps ON position.
  • Measure the voltage between the overhead console C930-4, circuit 484 (OG/BK), harness side and ground while rotating the instrument panel dimmer switch.
  • Does the voltage vary between 0 and 10 volts?
Yes
GO to A9 .

No
REFER to Section 413-00 for further diagnosis of the instrument cluster and panel illumination. A9 CHECK CIRCUIT 676 (PK/OG) FOR OPEN
  • Measure the resistance between the overhead console C930-2, circuit 676 (PK/OG), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation.

No
REPAIR the circuit. TEST the system for normal operation.

Nov 30, 2017 | Mercury Grand Marquis Cars & Trucks

1 Answer

How to reset compass


You have to go to a vacant car parking lot and go in a full lock circle 6 times clockwise and 5 times anticlockwise. Mine has a set button.

A known problem

http://lincolnforums.com/forums/threads/12036-2008-MKX-compass-problem

This one is a bit more helpful. Magnetic interference?



Compass Problem

Mar 16, 2016 | 2008 Lincoln MKX

1 Answer

Compass in the dash stop working


needs service.
the FSM covers this toy.

alldata.com read

or the real deal (FSM)
click jeep

https://www.techauthority.com/en-US/Pages/Home.aspx

RTM

Did you scan the PCM yet, if not why not, id bet there are errors there. like compass module not talking or?

Feb 24, 2015 | 2014 Jeep Grand Cherokee

1 Answer

My rear view mirror with temp and compass sometimes will not work. It will show all the digital shows up at once and not the temp, but sometimes it works ok. What can I do?


Does the compass work when the temperature goes out? If the compass still works then chances are that the ambient temp sensor is defective. Also, could be wiring to the sensor. If the compass goes out with the temperature then chances are the mirror itself is defective. Cheapest most common problem is the ambient temp sensor. It's behind the grill by the condenser at the front of the vehicle.

Aug 20, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Where is horn relay on a 2010 jeep compass


I need help on my 2010 jeep compass 2.4l the horn does not work I put a new horn in it worked for a couple of days and stopped working. Any one know if there's a fuse for the horn I can not find one ?

Apr 23, 2014 | 2007 Jeep Compass 2.0

1 Answer

2007 compass


yes it should it works with the brakes transmission and so on you need to check the codes the suspension and traction control are not working properly

Nov 03, 2013 | 2009 Jeep Compass

1 Answer

2007 jeep compass low beam doesnt work


Check the fuse for that side yes you have a fuse for each high and low beams for each side

Mar 26, 2013 | 2007 Jeep Compass 2.4

1 Answer

Compass module fallure escape 2008


I would check all fuses and replace any blown and retest. If the compass is still not working..I would make sure there is power at the compass module...If there is.. I would replace the module.

Nov 13, 2012 | 2008 Ford Escape

Not finding what you are looking for?
2005 Toyota Tacoma Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...