Question about 2000 Jeep Grand Cherokee

1 Answer

Rear differential how to pull axles - 2000 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 22,156 Answers

You have to remove the four bolts in the brake back plate ,then remove the rear cover on the diff ,then strip the planet gears ,then on the end of the half shaft is a horse shoe shape clip ,pull this out then the half shaft comes out

Posted on Nov 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the rear wheel hub on a 98 Z71


To change the bearing , you have to pull the axle. Jack the rear end up and use support jacks. Remove the differential cover, oil will come out. Put the transmission in neutral. Spin the differential until you see the bolt that holds the center pin, remove both. remove the tires. push the axle in. remove the clip one the end of the axle in the differential. pull the axle out. You can chisel the bearing out. But they do have tools that get them out.
26208027-ntpj3zzbu2souu1dk5yahwp3-4-0.gif

May 29, 2016 | Cars & Trucks

1 Answer

I have a 91 toyota previa and im trying to remove the rear differential..its a 2wd. I have unbolted the drive axle and the differential casing but its my understanding you have to pull lose the rear...


Most differentials are set up like this. There is a steel bar that is i the middle of the gears, this is held in with a bolt. remove the bolt. pull the bar out. Then push the axles in the center. There is a c clip to remove from the axle. They will come out easily. Pull the axles out. Once the axles are out the hog head as they call it, will come out. Just watch as the inner gears will come out also. And will have to be placed in the same spot. Kinda of push in and see. let me know

Aug 16, 2011 | 1991 Toyota Previa

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

2 Answers

I have greese all over the rear brakes


Rear Axle seals are bad, they must be replaced. Good Luck

Jan 14, 2011 | 1993 Ford Econoline

1 Answer

How do i take my passenger rear axle out of my 95 z71


Pull the cover off the rear differential. Remove the 5/16 headed bolt that holds the differential pin in. Remove the pin. Push the axle in and remove the C clip. Then pull out the axle. Replace the pin so the spider gears don't fall out if you turn the diff with the axle out.

Nov 11, 2010 | 1996 Chevrolet K1500

1 Answer

Rear axle removal ? i want to take to replace two broken lug nut bolts


to remove the rear axle you will need to put the rear of the jimmy on jack stands off the ground and remove the wheels

then remove the rear drums or if you have disc brakes the caliper and rotor

next you will need to remove the rear differential cover

once you have removed the rear differential cover you will need to rotate the differential by just turning the rear axle to gain access to the lockbolt

using an 8 mm socket you should be able to fairly easily remove the lock bolt

once you have removed the lock bolt you will need to push the axle in from the side that the wheel gets mouted to and then in the rear differential remove the locking 'c' clip

once the locking 'c' clip is removed you should be able to pull the axle right out

installation is the reverse of the removal

keep in mind that after romoving the lock bolt you must make sure not to rotat the axle if you do you will mess up the allignment with the differential and axle and you will spend loads of time trying to re-allign it again

hope this helps

Aug 13, 2010 | 1996 GMC Jimmy

1 Answer

How to remove gears from differential on a 95 mustang v6


Removal
  1. Raise vehicle and place jackstands under rear frame crossmember. Lower the hoist so that rear axle housing is at suitable working height.
  1. Remove axle housing cover from rear axle housing and drain lubricant.
  1. Perform the inspection before disassembly.
  1. Remove rear wheels, rear disc brake calipers and rear disc brake rotors.
  2. Working through cover opening, remove differential pinion shaft lock pin and remove differential pinion shaft and differential pinion gears (4215). 3fdbe2c.gif
NOTE: THIS IS FREE INFORMATION!!!!
  1. Remove rear brake anti-lock sensor . Push axle shaft inward until u-washers at button end of the axle shaft are clear of side gear recess.
  1. stb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage inner wheel bearing oil seals when removing axle shafts from rear axle housing. In addition, axle shafts should be completely removed from rear axle housing.
    Remove u-washers and pull axle shafts out of the rear axle housing. 85189ce.gif

Mar 25, 2010 | 1996 Ford Mustang

1 Answer

Clanging noise rear and rear don't pull


The axle probably lost a keeper ring on the inside of the differential and the pieces may be going through the differential and ring&pinion gearing making the noises you hear. You will need to drain the oil out, find the broken pieces, and inspect all gearing for broken/damaged teeth, and for any noisy bearings. Flush the case out with cleaning solvent. Re-insert the loose axle after cleaning and inspecting it well--especially the interior end. Replace the keeper (new) on the axle end inside the differential spider gearing. Inspect the brakes on the loose axle side for any oil deposits and for any damage that might have been caused when the axle came out. If the differential is badly damaged, it might be cheaper to find another rear end in a wrecking yard. Hope this helps!

Dec 26, 2009 | 1997 GMC Suburban

1 Answer

2002 dodge 1500 rear end making whining nosie


This could be one of several problems: If the noise increases with speed, and you are only hearing it from the rear differential and not the transmission, it could be the rear differential carrier bearings, or rear axle bearings going bad. If you are only hearing the noise upon acceleration or deceleration, the rear differential ring and/or pinion gears may be going bad and the rear differential will need an overhaul. You'll have to get the rear wheels off the ground and see if you can pinpoint the location of the noise with something such as a stethoscope. If it's coming from the rear differential, you'll need to pull the bolts and the cover to determine if the gears are still in good shape, or if there is any pitting. Same with the carrier bearings; if you see pitting/ discoloration, they'll need replacement. If the noise is coming from one side towards the end of the axle shaft near the wheel, it's most likely a axle bearing going bad, and you'll need to pull the wheels, remove the diff. cover to release the C clip which holds the rear axle in place at the differential, and pull the axle out. You also need a special tool with a slide hammer to remove the axle bearing and seal.

Nov 20, 2009 | Dodge Ram 1500 Cars & Trucks

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...